top of page

Jeep Flat-Tow Installation

Jeep Flat-Tow Installation
Jeep Flat-Tow Installation

Bring your Jeep on your next RV trip.

Jeep flat-tow installation and planning for 2016–2026 vehicles at Stellar Auto & Mobility Repair in West Melbourne, Florida. Start with the exact model, year, transmission and transfer case; a parts listing does not establish factory towing eligibility.

Choose the correct Jeep application

Wrangler JK: 2016–2018. Wrangler JL: 2018–2026. Gladiator JT: 2020–2026. Both JK and JL were sold for 2018. Wrangler 4xe requires the correct factory and hybrid information plus separate brake-assist and electrical checks. Cherokee, Grand Cherokee/L, Compass, Patriot and Wagoneer applications require exact-year review; this guide does not automatically approve those combinations.

A complete towing installation

Compare baseplates or another expressly approved attachment, a compatible tow bar and safety cables, supplemental braking and breakaway, coach-to-Jeep lighting, charging where required, and any motorhome receiver or height-adapter work. Check the lowest applicable capacity against actual loaded weights. Do not assume recovery hooks or D-rings are approved for flat towing.

Factory manuals and towing pages

Use the complete exact-year chapter, including its warnings, verification check and return-to-driving procedure. Transfer-case Neutral and transmission Neutral are different. Do not copy a procedure from another Jeep.

2016 Wrangler JK — factory towing pages · PDF pages 575–579. Full owner manual

2017 Wrangler JK — factory towing pages · PDF pages 324–327. Full owner manual

2018 Wrangler JK — factory towing pages · PDF pages 320–323. Full owner manual

2018 Wrangler JL — factory towing pages · PDF pages 373–376. Full owner manual

2019 Wrangler JL — factory towing pages · PDF pages 399–402. Full owner manual

2020 Wrangler JL — factory towing pages · PDF pages 208–210. Full owner manual

2021 Wrangler JL — factory towing pages · PDF pages 170–171. Full owner manual

2022 Wrangler JL — factory towing pages · PDF pages 170–172. Full owner manual

2023 Wrangler JL — factory towing pages · PDF pages 171–172. Full owner manual

2024 Wrangler JL — factory towing pages · PDF pages 205–207. Full owner manual

2025 Wrangler JL — factory towing pages · PDF pages 206–208. Full owner manual

2026 Wrangler JL — factory towing pages · PDF pages 220–221. Full owner manual

2020 Gladiator JT — factory towing pages · PDF pages 208–210. Full owner manual

2021 Gladiator JT — factory towing pages · PDF pages 171–173. Full owner manual

2022 Gladiator JT — factory towing pages · PDF pages 175–177. Full owner manual

2023 Gladiator JT — factory towing pages · PDF pages 174–176. Full owner manual

2024 Gladiator JT — factory towing pages · PDF pages 160–161. Full owner manual

2025 Gladiator JT — factory towing pages · PDF pages 149–151. Full owner manual

2026 Gladiator JT — factory towing pages · PDF pages 170–171. Full owner manual

Baseplate options and application checks

Blue Ox BX1126 — 2007–2018 JK with standard factory bumper Standard-bumper JK application. Verify special editions, accessories and exact installation revision. This is not a JL bracket.

Blue Ox BX1134 — JK special factory bumper application Manufacturer lists 75th Anniversary applications and a separate metal-bumper application. Confirm the exact model year and special bumper before ordering; this does not replace BX1126 based on model year alone.

Roadmaster Direct-Connect 521448-5 — JK standard factory bumper; special editions excluded 2017 JK FitMaster branch: standard bumper and plastic skid plate; excludes aftermarket bumpers, winches, guards, Call of Duty, BackCountry, Winter Edition, Recon, 10th and 75th Anniversary versions. Verify other years separately. Direct-Connect does not use the Roadmaster crossbar.

Roadmaster Crossbar-Style 521448-4 — JK crossbar alternative — confirm exact application A separate connection choice. Verify the exact bracket fitment, required crossbar and compatible accessories. Retain for comparison; current application review is still required.

Roadmaster Direct-Connect 521455-5 — JK with specified Warn Elite bumper 2017 FitMaster identifies Warn Elite 101420, with a winch permitted and without the lower valance. Other aftermarket bumpers need their own approval.

etrailer Invisible e98949 — JK standard factory bumper Own-brand catalog and 2016 installation reference located. Verify special-edition exclusions and accessory clearance. A winch guard or different bumper can change the application.

Demco Tabless 9519292 — JK standard-bumper application; 2017 manufacturer lookup verified Demco lists 9519292 for the 2017 Sport, Sahara, Rubicon, Black Bear, Unlimited and Willy branch. TP29292 Rev 4 (02/21) is available. Verify each adjacent year and the exact bumper before quoting.

Blue Ox BX1139 — JL; manufacturer includes 4xe, 392 and factory bumper/winch applications Read the current manual against the exact vehicle and front equipment. An aftermarket bumper requires separate review. This is different from the Gladiator BX1145.

Roadmaster Direct-Connect 521453-5 — JL standard factory bumper; selected 2025 JT trims 2024 Wrangler and 2025 Gladiator FitMaster branches reviewed. For 2025 JT: Sport, Sport S, Willys, Overland, Rubicon, Rubicon X and High Altitude; excludes Mojave, winches and aftermarket bumpers. Verify engine, exact year and bumper before ordering.

Roadmaster Crossbar-Style 521453-4 — JL crossbar alternative — confirm exact application Keep crossbar and Direct-Connect equipment distinct. Verify bracket application, crossbar assembly, tow-bar ends and any shield or rock-guard restrictions.

Roadmaster Direct-Connect 521463-5 — JL factory steel bumper and winch branch 2024 FitMaster identifies this separate steel/winch application. Confirm current year coverage and the factory winch arrangement; do not substitute the standard 521453-5.

Demco Tabless 9519336 — JL / JT standard bumper branch — verify exact trim Current manufacturer fit-list returns 9519336 for the 2024 JL standard-bumper branch and the 2024 Gladiator Sport, Sport S and Overland standard-bumper branch. Confirm other years and trims independently. Use the current TP29336 instructions.

etrailer Invisible e98948 — JL / JT plastic bumper; exclusions apply Reviewed own-brand listing excludes Gladiator Rubicon and Mojave. The reviewed 4xe range ends at 2023. Later 4xe applications must not be inferred. Exact trim and current instructions control.

Blue Ox BX1145 — Gladiator JT; instructions include Mojave and adaptive cruise Match the actual factory bumper, winch equipment and current manual. Do not substitute Wrangler BX1139 on the strength of a similar-looking front end.

Roadmaster Direct-Connect 521454-5 — Gladiator Mojave; 2025 manufacturer branch verified The 2025 FitMaster branch is Mojave only, excluding Mojave X, factory winch-capable steel bumpers and aftermarket bumpers. Adjacent-year applications require their own current lookup.

Roadmaster Direct-Connect 521466-5 — 2025 JT Mojave / Mojave X factory steel winch branch The current 2025 FitMaster branch identifies Mojave and Mojave X with the factory winch-capable steel front bumper, with or without the specified Mopar winch. Match bumper and winch-mount part numbers to current Roadmaster instructions before ordering; aftermarket arrangements need separate approval.

Demco Tabless 9519339 — 2024 Wrangler Rubicon JL with taller metal bumper Current manufacturer fit-list returns 9519339 and TP29339 for this specific steel-bumper branch. Confirm winch equipment, exact bumper and installation revision before ordering.

Demco Classic 9518320 — 2017 Rubicon Hard Rock / Rubicon X / 75th Anniversary Current Demco 2017 fit lookup identifies the taller-metal-bumper branch. Classic connection: verify the exact tow-bar interface and adapters. TP20320 Rev 2 (11/16).

Demco Tabless 9519331 — 2017 JK Winter Edition / Back Country Current Demco 2017 fit lookup identifies this special-bumper branch. TP29331 Rev 1 (02/21). Match the actual bumper and current manufacturer application before quoting.

Braking, wiring and charging

Choose braking for both the Jeep and motorhome brake system. Portable brakes still require a suitable power supply, breakaway installation and proper setup. Installed systems need functional and full-release checks. Lighting receives motorhome signals; the Jeep trailer-output socket is a different function. Verify charge-circuit protection, grounds and voltage under load. The 4xe application needs specific brake-assist and monitoring review.

Downloads

Stellar Jeep Manuals and Resources (PDF)

Stellar Jeep Departure Checklist (PDF)

Jeep flat-tow questions and answers

1. Can every Jeep be flat towed?
No. The model year, transmission and transfer case determine eligibility. A baseplate listing does not override Jeep’s factory instructions. Start with your exact vehicle and manual; unknown combinations in this guide remain in application review.

2. Which model years does this guide cover?
The selector covers 2016–2026 and offers an unsure-year option. Exact factory towing chapters are linked for the reviewed Wrangler JK, Wrangler JL and Gladiator years. Other Jeep families have selected research references and require an exact-year review before a towing package is approved.

3. Is my 2018 Wrangler a JK or a JL?
Both generations were sold for 2018. Confirm the generation using the VIN and vehicle records, then select that generation’s manual and bracket application. A 2018 Wrangler description alone is not enough to order the correct baseplate.

4. Does four-wheel drive automatically mean flat-towable?
No. Transfer-case design and the factory towing table matter. Some Jeep systems have an approved Neutral procedure; others prohibit four-down towing. A 4WD badge, a transmission Neutral position or a tow rating does not establish recreational-towing eligibility.

5. Can a Wrangler with an automatic transmission be flat towed?
The linked Wrangler factory manuals contain recreational-towing procedures for the applicable 4WD automatic configurations. They distinguish transfer-case Neutral from the automatic transmission position. Read the complete exact-year chapter and verify the actual vehicle before setting it up.

6. Is a manual-transmission Wrangler prepared the same way?
The transfer case and transmission still have different jobs, and the manual-transmission position must follow the factory instructions. Do not copy the automatic sequence or assume leaving the gearbox in Neutral is correct. Open the chapter for your year and transmission.

7. Can a Wrangler 4xe use the same towing setup as a gas Wrangler?
Use the correct year’s Wrangler manual and applicable hybrid supplement. The front equipment, brake-assist behavior, brake monitoring and electrical requirements need separate verification. Do not transfer a conventional vacuum-brake setting or another vehicle brand’s hybrid procedure to a 4xe.

8. Are all Grand Cherokees flat-towable?
No. Reviewed factory guidance distinguishes approved low-range transfer-case configurations from 2WD and single-speed systems. Year, generation, powertrain and transfer case must be identified. This guide does not automatically approve a Grand Cherokee or Grand Cherokee L selection.

9. What about Cherokee, Compass, Patriot and Wagoneer?
They cannot share one eligibility rule. The reviewed 2016 Cherokee guidance distinguishes two-speed PTU equipment, while the 2026 Cherokee prohibits four-down towing. The reviewed 2016 Compass and Patriot guidance distinguishes manual from automatic transmissions. Other years and Wagoneer configurations require their own factory review.

10. Does the Jeep’s trailer tow package make it ready to tow behind an RV?
No. A trailer package supports towing a trailer with the Jeep. Flat towing behind a motorhome needs an approved vehicle procedure plus the correct attachment, tow bar, cables, supplemental brake, lighting and any required charging equipment.

11. Can I just put the transmission in Neutral?
Do not use that shortcut. Wrangler and Gladiator procedures distinguish transfer-case Neutral from the transmission position. Follow the exact-year instructions in order, including the no-movement check and the specified shutdown state.

12. How do I put my Jeep into its towing configuration?
Select the year, generation and drive system, then open the factory towing pages. Follow the complete sequence for your transmission, including brake use, ignition and engine state, transfer-case operation, verification and final transmission position. This guide deliberately avoids one universal sequence for every Jeep.

13. How do I know the transfer case is actually in Neutral?
Complete the exact no-movement or verification procedure specified by Jeep. A lever position or indicator alone is not a substitute for the prescribed check. If the result does not match the manual, stop the preparation and resolve the cause before towing.

14. Should the automatic transmission be in Park while towing?
The linked Wrangler and Gladiator chapters specify the transmission position after transfer-case Neutral is established. Use your exact manual and follow its order; do not extrapolate that position to another Jeep model or apply it before the required checks.

15. Should the parking brake be released?
It must be in the state prescribed by the factory towing procedure before movement. During hookup and unhooking, control the vehicle with the brakes and other measures directed by the manuals. Do not release restraint until the combination is securely controlled.

16. Do I leave the key or ignition on?
Ignition and steering requirements vary with year and system. Follow the selected factory chapter, including its final engine and ignition state. Do not copy a key-position instruction from a different Wrangler generation or from a different Jeep model.

17. Do I need to disconnect the battery?
Do not add or omit a battery-disconnection step based on general towing advice. Check the exact vehicle manual and the selected brake, lighting and charging instructions together. A required power supply or breakaway function must still work in the prescribed towing state.

18. Can I back up with the Jeep attached?
Disconnect first. Reverse movement can force the steering or tow-bar geometry into a damaging position. Plan fuel stops, campground entrances and parking with a forward exit, and follow the bar manufacturer’s maneuvering limits.

19. Is there one speed limit or restart interval for all Jeeps?
No universal figure is provided here. Use the vehicle and equipment manuals for speed, distance, inspection and operating restrictions. The motorhome, tow bar, tires and other components may impose additional limits; use the applicable most restrictive requirement.

20. How do I return the Jeep to normal driving?
Use the complete return-to-driving procedure in the same factory chapter, not the entry steps in reverse from memory. Secure the vehicles before disconnecting, restore the specified transfer-case and transmission states, and verify normal operation before driving away.

21. What equipment belongs in a complete flat-tow quote?
The plan should cover the vehicle attachment, compatible tow bar, safety cables, supplemental brake and breakaway, coach-to-Jeep lighting, any required charging and monitoring, and coach-side height or receiver work. Include installation, setup checks and an owner walkthrough.

22. Which baseplate fits my Jeep?
Start with the exact year, generation, trim and front bumper. Check winch equipment, guards and special editions against the current manufacturer fit list and installation manual. The guide’s part-number cards are comparison candidates, not a VIN-specific order approval.

23. Does a factory steel bumper or winch change the baseplate?
It can. Standard plastic, factory steel, factory winch and aftermarket arrangements can have different brackets or exclusions. Record the bumper and winch-mount part numbers and compare the actual front end with the current kit instructions before ordering.

24. Why do Gladiator Mojave and Mojave X need extra checking?
Those names do not establish the same front attachment. Manufacturer fit lists distinguish Mojave, Mojave X, bumper and winch configurations. Review the exact branch and current instructions; do not select a bracket merely because another Gladiator uses it.

25. Can I attach the tow bar to recovery hooks or D-rings?
Only use an expressly approved flat-towing arrangement. A recovery point or aftermarket bumper is not automatically rated for highway flat towing. Obtain the bumper manufacturer’s written approval and verify the exact adapters, dimensions, ratings and safety-cable attachment points.

26. Can I mix tow-bar and baseplate brands?
Only with the exact approved connection or adapter. Verify both part numbers, attachment ends, crossbar requirements and capacities. Similar-looking tabs and pins are not proof of compatibility; include the required adapters in the quote.

27. Can I reuse my existing tow bar or brake?
Possibly. Provide clear model and serial-label photos, complete hardware, service history and receiver details. Inspect wear and missing parts, check applicable recalls and confirm manufacturer compatibility with the Jeep and motorhome before relying on the equipment.

28. Does a stronger tow bar increase my motorhome’s towing capacity?
No. Coach, chassis, receiver, combination weight, adapters, cables and bar limits still apply. Use the loaded Jeep’s actual weight and all cargo in the capacity review. A high number on one component does not raise another component’s rating.

29. Do a lift kit or larger tires change the installation?
They can change connection height, steering geometry, loaded weight and clearance. Measure the loaded motorhome receiver and Jeep attachment height. Use only approved height adapters and stay within the equipment’s specified geometry and ratings.

30. Can the installation be reversed without visible changes?
Removable arms can come off for normal driving, but the exact bracket installation may require fascia trimming or drilling. Review the kit instructions and appearance expectations before approval. Removable does not necessarily mean every installation change is reversible.

31. Why does the Jeep need supplemental braking?
A compatible system applies the Jeep’s service brakes and provides the selected system’s breakaway function. It must suit the Jeep and motorhome and satisfy applicable travel-route requirements. Capacity and braking are separate checks; a suitable tow bar does not supply braking.

32. Will my motorhome’s trailer brake controller operate the Jeep brakes?
A conventional trailer brake controller is not automatically a towed-vehicle braking system. Identify the complete system that applies the Jeep’s brake pedal or service brakes, handles separation and provides driver feedback. Confirm any required coach-side components.

33. Should I choose a portable or permanently installed brake?
Compare the motorhome brake type, Jeep brake-assist system, setup work each trip, monitoring and whether the equipment will move between vehicles. Portable systems need proper positioning and attachment each trip; installed systems still require pre-trip functional checks.

34. Does a portable brake mean no installation is needed?
No. Breakaway mounting, wiring and a reliable power source still need attention. Verify pedal attachment, floor and seat support, clearance and setup according to the brake manual. Test operation and full release in the actual towing configuration.

35. Why does the motorhome’s air or hydraulic brake system matter?
It affects which supplemental brake arrangement and coach-side installation are appropriate. Identify the motorhome system before selecting equipment; do not assume every installed brake kit connects to every coach. Review both vehicle-side and coach-side instructions.

36. What needs special attention on 4xe braking?
Confirm how the vehicle’s brake assist behaves in the factory-prescribed towing state, and use equipment approved for that application. Verify the brake’s required settings, monitoring method, power and full pedal release. A generic vacuum-brake procedure is not an adequate 4xe setup check.

37. What does the breakaway system do?
It is designed to apply the supplemental brake if the vehicles separate, according to that equipment’s design. Mount and route it exactly as specified, preserve its required power and test it as directed. Safety cables and the breakaway system serve different functions.

38. Does every plug-in light harness fit every Wrangler JL?
No. Year, lamp equipment and tow-package restrictions matter. The reviewed Blue Ox BX88368 application excludes 2025–2026 JL, so it must not be carried into those years by assumption. Confirm the current harness application and test all signals after installation.

39. Why might I need a charge line?
Brake equipment and vehicle systems can draw from the 12V battery during towing. Check the actual demand and equipment requirements, then verify the coach supply, protection, grounds, connector and voltage under load. A charge line is distinct from tail-light wiring.

40. Does the factory trailer socket provide flat-tow lighting?
A trailer-output socket sends signals from the Jeep to a trailer. Flat-tow lighting receives the motorhome’s signals. Verify the appropriate receiving circuit, isolation, grounds and brake-signal behavior; test running lights, left and right turns and braking in the actual towing state.

41. What if the Jeep moves during the factory verification check?
Stop preparation and maintain control using the service and parking brakes as the manual directs. Recheck the correct sequence and actual transfer-case state. If it will not pass the prescribed check, arrange diagnosis before towing; do not treat the test as optional.

42. What if the transfer case will not shift?
Do not force it or substitute another Jeep’s sequence. Check the exact manual’s transmission, ignition and engine-state instructions and any prescribed conditions for shifting. Persistent difficulty needs diagnosis before the Jeep is towed.

43. Why is the Jeep battery going dead behind the RV?
Check battery condition, actual tow-state draw, brake power needs, coach output, cord terminals, grounds and voltage drop under load. A charge wire being present does not prove it is charging. Find the cause of any blown fuse before replacing it repeatedly.

44. What if the brake monitor stays on or the Jeep drags?
Stop safely and investigate before continuing. Check brake positioning, pedal attachment, cable travel, assist settings and complete brake release according to the equipment instructions. Do not try to overcome the drag with more motorhome throttle.

45. What if the Jeep lights disagree with the motorhome?
Check connector functions, grounds, harness application, diode or smart-diode requirements and brake-signal override behavior. Test in the actual towing state, including combined braking and turn signals. Correct the fault before departure.

46. What if the Jeep steering oscillates or the tow-bar arms bind?
Stop in a safe location. Steering oscillation needs a review of exact-year steering provisions, tires, alignment, attachment geometry and installation condition. For a bound arm, secure both vehicles and use the bar manufacturer’s release procedure; do not hammer loaded pins or work between uncontrolled vehicles.

47. Can the installation affect driver-assistance sensors?
Sensors, wiring, fascia and mounting hardware may be near the work. Verify the approved application and required clearance, inspect for faults and follow applicable vehicle service requirements. Discuss added bumpers, guards or winches before selecting the bracket.

48. How much does a complete installation cost, and what does Stellar need?
An accurate estimate needs the Jeep VIN, trim, bumper photos, motorhome details, existing equipment labels and travel timing. The estimate should separate attachment, tow bar, braking, lighting, charging, coach-side work and verification. The email button carries your selection into a draft for you to complete and send.

49. Are the pictures actual Stellar customer installations?
The real vehicle photos are credited licensed references. Installed bracket photos are labeled Roadmaster manufacturer references. They are not presented as Stellar customer work. Use the pictured part number and application label when comparing your front end.

50. Where are the downloads, and can I see the whole guide?
Open your matching factory manual card for the full PDF, towing-page link and print/save page range. Separate downloads provide a manual directory and departure organizer. Choose Show the entire guide for the full reference view. The guide and checklist organize the work; the exact vehicle and equipment manuals remain controlling.

Plan your Jeep installation

Have the VIN, trim, front-bumper photos, motorhome details, existing equipment labels and travel timing ready. Call 321-477-1234 or email Stellar. Final equipment selection requires the current factory and manufacturer instructions for the actual vehicle.

Reference photos are credited licensed vehicle images and labeled manufacturer installation examples. They are not presented as Stellar customer work.

Servicing Brevard County vehicles since 2019

Our Services

PREVENTATIVE MAINTENANCE

Professional Oil Change Service

TIRES & ALIGNMENTS

VEHICLE INSPECTION

FLEET MANAGEMENT

Trailer Hitch & Flat-Tow Installation

Maverick Flat-Tow Installation

Jeep Flat-Tow Installation

MOST MOBILITY REPAIR

MOST AUTO REPAIR

PARTS SALES

TECHNICAL SUPPORT

Opening Hours

MONDAY

TO

8:30 AM

5:00PM

TUESDAY

TO

8:30 AM

5:00PM

WEDNESDAY

TO

8:30 AM

5:00PM

THURSDAY

TO

8:30 AM

5:00PM

FRIDAY

TO

8:30 AM

5:00PM

SATURDAY

APT

BY

ONLY

SUNDAY

APT

BY

ONLY

Contact Us

7791 Industrial Rd.
West Melbourne, FL 32904 USA

​

Office: 321-477-1234
info@stellarautoandmobility.com

Stellar Auto & Mobility Repair Map Location

© 2024 by Stellar Auto & Mobility Repair

Veteran Own Small Business
Stellar Auto & Mobility Repair Logo
bottom of page