top of page

The Stellar guide · Ford Maverick Hybrid

Ford Maverick.
Flat-tow guide.

A complete flat-tow resource for RV owners: model-year eligibility, installed baseplate photos, equipment comparisons, wiring, charging and the steps that matter before you leave.

Silver 2024 Ford Maverick Hybrid Lariat, full vehicle side view
Real vehicle reference · RL GNZLZ, brightness edit by Alex Neman · Photo source · CC BY-SA 4.0
2022–2026 model-year guidanceRoadmaster · Blue Ox · Demco · etrailer · CURT · NSAInstallation in West Melbourne, Florida

01 / Model-year fitment

Can your Maverick be flat towed?

Choose your truck to filter Ford instructions and baseplates. Then open one section at a time. All of the information stays available.

Where would you like to start?

Follow the guide in order, or begin with the question you have today. Every topic stays within reach as you read.

I’m new to flat towing Explain the whole setup from the beginning →I’m choosing equipment Compare applications, tradeoffs, photos and manuals →I have products in mind Review my inquiry and ask for information or pricing →
Your model yearChoose a model year202220232024202520262027 or later / not surePowertrainChoose your powertrain2.5L Hybrid FWD2.5L Hybrid AWD2.0L EcoBoostNot sure
See my guideReset selectionResults also update as you choose.Browse without selecting a vehicle
Your next step
Choose your year and powertrain for a starting point. Final fitment requires the VIN, equipment and current manuals.
See the full year / powertrain eligibility chartTap to readTap to close
Maverick configurationFour-down RV towingStart here
2022–2024 · 2.5L Hybrid FWDEligible when Ford’s procedure is followedEarlier front-end baseplate family. Use the manual for the exact model year.
2025–2026 · 2.5L Hybrid FWDEligible when Ford’s procedure is followedRefreshed front end. Recheck baseplate application, fascia and driver-assistance equipment.
2025–2026 · 2.5L Hybrid AWDEligible when Ford’s procedure is followedHybrid AWD is different from EcoBoost AWD. Verify VIN and current manufacturer application.
2.0L EcoBoost · FWD or AWDNot approved for recreational four-down towingA tow bar or baseplate does not make this powertrain eligible. Discuss an approved transport method.
2027 or later / uncertain vehicleDo not assume carryover approvalObtain the exact Ford manual and current baseplate application before selecting parts.
The 4K Tow Package answers a different question.Read this important informationTap to close
The 4K Tow Package answers a different question.It describes what the Maverick can pull as a tow vehicle. It does not establish whether a motorhome may pull that Maverick with all four wheels down.
Back to guide topics ↑
Ford Maverick Flat-Tow GuideYour Maverick guide
Change truck
0 products selectedReview my inquiry →
Topics ↓
Choose a topicAll sectionsYour complete setupYour Ford manuals & downloadsYour Ford towing instructionsMatching baseplatesTow bars & connectionsBraking & breakawayLighting & wiring12V chargingInstallation processInstalled photosDeparture checklistTroubleshootingQuestions & answersEquipment manualsRequest an estimateAll topics

Explore the guide

What would you like to see?

Tap one of the four large buttons below. Details stay closed until you want to read them.

Show the entire guide on one page

For browsing every year or printing a complete reference.

Save it for the road

Ford manuals. Just the tow pages. Ready to save.

Pick your model year to open the full factory manual or go straight to Ford’s recreational-towing section.

20222023202420252026All years
2022 Ford manual and flat-towing pagesView 3 manual / download choicesTap to close
2023 Ford manual and flat-towing pagesView 3 manual / download choicesTap to close
2024 Ford manual and flat-towing pagesView 3 manual / download choicesTap to close
2025 Ford manual and flat-towing pagesView 3 manual / download choicesTap to close
2026 Ford manual and flat-towing pagesView 3 manual / download choicesTap to close
How to save only the Ford flat-towing pagesTap to readTap to close
  1. Open the full manual or “Open exact PDF pages” for your year.
  2. Select Print, then enter the PDF viewer page range shown above. It differs from the page number printed on the document.
  3. Choose Save as PDF and check the preview before saving. Keep the complete manual available too.

Some phone PDF viewers ignore page-jump links. Enter the listed PDF page number manually. “Flat-tow section only” opens Ford’s separate online section, which you can also print or save.

Match the vehicle and the manual edition.Read this important informationTap to close
Match the vehicle and the manual edition.The PDFs above are dated Ford editions. Ford’s online section may be revised. Confirm your VIN, powertrain and ignition type; follow the applicable current instructions and resolve any differences before towing. Do not combine steps from different model years.
Download the Stellar resource kitTap to readTap to close
Two useful downloads

Keep a resource kit with your RV documents.

Original Stellar quick references with links back to the controlling manuals.

Manufacturer catalogs, fitment finders & recall informationTap to readTap to close

Sources checked November 2026. Documents open at their original publisher; use the viewer’s download control to save a copy. The Brake Buddy manual is a manufacturer document hosted by ManualsLib because the original publisher download was unavailable during review. Some files are large. A product manual does not by itself establish Maverick fitment.

Choose another section ↑
Choose another topicNext section →

Manufacturer document library

50 equipment documents and resources. Search a part number, or open a category below. Every listed baseplate, tow bar and brake has instructions linked here and at the top of its product details.

Find a documentEquipment categoryAll equipmentBaseplatesTow barsBrakingLighting & 12V electricalChecklists & service information

Showing 50 documents

Baseplate instructionsView documentsTap to close
Tow-bar manualsView documentsTap to close
Brake-system manualsView documentsTap to close
Lighting, wiring & 12V charging instructionsView documentsTap to close
Checklists and Ford service informationView documentsTap to close

No matching documents. Try a brand, part number or a different category.

Choose another topicNext section →

Equipment / Baseplates

Compare Maverick baseplates.

Tap an option to open it. Tap it again to close it.

Understand the choice

The baseplate determines your truck-side connection

A baseplate spreads towing loads into specified structural mounting points. Its removable arms or tabs provide the connection you use each trip. “Removable” describes those attachment pieces, not the entire structure behind the bumper. The important comparisons are the exact vehicle application, connection style, installation changes and daily handling.

Direct-Connect vs Crossbar-Style

Roadmaster’s -5 Direct-Connect kits omit the separate crossbar. Its -4 Crossbar-Style kits serve a different interface and can suit an existing crossbar-dependent bar or accessory. The simpler-looking kit is not automatically compatible with equipment you already own.

Blue Ox tabs vs Demco/etrailer arms

BX2913 and BX2917 use the Blue Ox tab interface. Demco 9519360/9519366 and the listed etrailer applications use their specified removable connecting hardware. Match the actual tow-bar ends; adapters are named parts with their own limitations, not interchangeable pins.

Front-end modifications are a real tradeoff

Compare fascia cuts, shutter work, drilling, sensor clearance and the appearance with arms removed. For example, Blue Ox’s BX2917 instructions explicitly say shutters remain off. Decide whether that installation meets your expectations before selecting by appearance or price.

Compare the same installed scope

A useful quote includes the bracket, required connection pieces, specified hardware, installation, socket and breakaway mounting, and a complete hookup demonstration. A cheap bracket plus missing adapters may not be the least expensive complete system.

2025 XL exception to resolve: Roadmaster’s earlier-body FitMaster record mentions 2025 XL while its 2025 record lists the newer 524480-5. Both records are linked in the product details. Have Roadmaster or the installer resolve the actual fascia/application instead of assuming that the year filter alone settles this overlap.

Open a product below for its specific application, two-sided comparison, example, instructions and photos. The pros and cons explain practical selection tradeoffs; they are not claims of comparative road testing.

All applications2022–2024 Hybrid2025–2026 Hybrid

Showing 10 application options

Roadmaster Direct-Connect · 524480-5Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Roadmaster lists 2025–2026 Maverick XL, XLT and Lariat with the 2.5L Hybrid. Its application excludes tow hooks and aftermarket fog lights. This is the Direct-Connect interface for Roadmaster motorhome-mounted bars with the correct Roadmaster ends.

What it does and who it suits

Choose this when you want the tow-bar arms to attach to the removable truck-side arms without handling a separate crossbar. The permanent mounting structure remains behind the front fascia when the arms are removed.

Pros — reasons to choose it

  • One less crossbar assembly to connect, remove and store at a campsite.
  • Removable arms reduce the visible towing hardware during everyday driving.

Cons — tradeoffs and limits

  • Does not accept the Roadmaster crossbar: StowMaster and crossbar-dependent accessories are not a direct match. Roadmaster identifies Tow Defender 4750, not 4700, for this interface.
  • The vehicle-specific work includes trimming; a clean finished appearance does not mean the truck stays unmodified.

Example in practice

A 2025 Hybrid owner choosing Nighthawk 676 can compare this Direct-Connect arrangement with the -4 crossbar version. Nighthawk 677 has Blue Ox ends, so the same model-family name would not establish the same connection.

Complete the application

Include the exact tow-bar ends, safety-cable anchor arrangement, socket and breakaway mount in the installation plan. Measure finished pin height with the actual truck loaded for travel.

Product instructions ↗ · Manufacturer application / specifications ↗

2025–2026 Hybrid

Roadmaster Direct-Connect

524480-5

RM87NQ

Removable arms connect to compatible Roadmaster motorhome-mounted bars without a separate crossbar. A clean starting point when you want a Roadmaster system.

Fitment & installation details

Verify the current fit list, front-end options and tow-bar ends. Direct-Connect and Crossbar-Style arms are different interfaces. Protective screens and rock guards have their own compatibility restrictions; the bracket name alone does not approve every accessory.

Manufacturer PDF
Blue Ox · BX2917Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Blue Ox lists BX2917 for 2025–2026 Maverick HEV, including adaptive cruise control and shutters. It uses removable Blue Ox tabs and connects to suitable Blue Ox-style tow-bar ends.

What it does and who it suits

This is the refreshed-body Blue Ox application. It is a practical starting point for an owner keeping an approved Alpha, Avail or other bar already fitted with Blue Ox ends.

Pros — reasons to choose it

  • Removable tabs keep the everyday front appearance relatively unobtrusive.
  • Blue Ox publishes a specific Maverick installation manual and lists BX8848 as its wiring option for this application.

Cons — tradeoffs and limits

  • The BX2917 instructions say the shutters are removed and remain off. Fascia removal, drilling and trimming are also described; the pedestrian-alert speaker is reinstalled.
  • A Roadmaster-ended or Demco-ended bar needs the expressly approved connection arrangement; the baseplate is not a universal attachment.

Example in practice

A 2026 Hybrid Lariat owner with an Avail first confirms the receiver version and bar condition, then compares BX2917 installation changes against the other baseplates. The owner should see the shutter instructions before approving the work.

Complete the application

The manual gives a reference tab height of 15 inches and width of 26 inches. These help explain the layout; actual installed height must still be measured for tow-bar leveling.

Product instructions ↗ · Manufacturer application / specifications ↗

2025–2026 HEV

Blue Ox

BX2917

BLU94ER

Removable-tab baseplate listed by Blue Ox for the refreshed Maverick HEV, including applications with adaptive cruise and shutters.

Fitment & installation details

Check the installation revision against the exact truck. A catalog description that mentions shutters identifies the application; it does not promise that all shutter pieces remain unchanged. Confirm trimming and sensor clearance before installation.

Manufacturer PDF
Demco Tabless · 9519366Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Demco manual TP29366 identifies the 2025 Ford Maverick. This entry is not a confirmed 2026 application: obtain Demco’s current approval for that year rather than extrapolating from similar bodywork.

What it does and who it suits

The tabless system uses removable connecting tabs at the front of the truck. Compare it when selecting a Commander 2, Dominator or Excali-Bar 3 with the appropriate Demco connection.

Pros — reasons to choose it

  • Tabs remove when the truck is driven by itself.
  • Demco supplies an application-specific mounting layout and a parts breakdown, useful for checking whether a proposed or used kit is complete.

Cons — tradeoffs and limits

  • The instructions describe lower-shutter changes and air-cooler clearance work. Compare those changes before choosing solely by the visible front appearance.
  • The printed reference height is not a promise of a level connection to every motorhome; tires, loading and coach receiver height affect the finished setup.

Example in practice

An owner choosing the lighter Dominator can build a Demco connection around 9519366, but still needs a separately selected brake, lighting circuit and charge path. A matching brand does not supply those other functions.

Complete the application

Reference dimensions in TP29366 are 14½-inch pin height and 24-inch centers. The correct number is 9519366; 9519336 is not the Maverick substitute.

Product instructions ↗

2025 manual · verify 2026

Demco Tabless

9519366

DM38CV

Removable connecting tabs provide the truck-side interface for an approved Demco-style combination. The manufacturer part number is 9519366.

Fitment & installation details

Demco instruction TP29366 identifies the 2025 Maverick. Confirm the latest application approval for 2026 before ordering. The instructions call out lower-shutter changes and possible air-cooler clearance work. 9519336 is a different vehicle application and must not be substituted.

Manufacturer fitment catalog
etrailer Invisible · e96GVClick for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

This is the refreshed-front-end etrailer Maverick baseplate entry. Use its current e96GV Hybrid fitment and LIT-00942 instructions; do not substitute the earlier e64FV because the removable arms look alike.

What it does and who it suits

The removable-arm layout is worth comparing for an owner considering the etrailer SD or XHD connection. Compare the complete installed package, including any expressly required end adapter.

Pros — reasons to choose it

  • Removable arms reduce protruding hardware when not towing.
  • A matching documented bar/baseplate arrangement can simplify ordering and keep the connection hardware consistent.

Cons — tradeoffs and limits

  • Invisible describes the removable towing interface, not a guarantee that every mount or opening disappears. Review the installed photos with the arms removed.
  • A low baseplate-only price can exclude adapters, the front socket, breakaway mounting and installation labor. Compare identical scopes.

Example in practice

A refreshed-body Hybrid owner comparing e96GV with a Roadmaster Direct-Connect kit should compare front-end modifications and the chosen bar’s attachment ends, not just the steel bracket price.

Complete the application

Have the quote identify both full part numbers, the approved connecting ends and which installation parts are supplied. Keep the instruction sheet with the installation record.

Product instructions ↗

2025–2026 · confirm trim

etrailer Invisible

e96GV

Brand catalog part number

Removable-arm option for the refreshed front end. Include this brand when comparing appearance, interface and the cost of a complete installed system.

Fitment & installation details

Confirm the current Hybrid application and instruction revision before purchase. Compatibility depends on the exact tow-bar ends; a brand match or similar-looking tab is not sufficient. Any adapter must be approved for both components.

Roadmaster Crossbar-Style · 524480-4Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

The refreshed-body Roadmaster Crossbar-Style application uses a different truck-side connection from 524480-5. Select it for an approved Roadmaster crossbar arrangement, not as an interchangeable spelling of Direct-Connect.

What it does and who it suits

A crossbar links the two removable truck-side assemblies and creates the interface required by certain Roadmaster bars or accessories. Its value is connection compatibility, not an automatic increase in towing capacity.

Pros — reasons to choose it

  • Can retain an existing approved crossbar system instead of replacing equipment unnecessarily.
  • Provides the crossbar-style interface required by applicable accessories.

Cons — tradeoffs and limits

  • Adds a separate assembly to handle and store. It can leave a busier-looking connection while set up for towing.
  • The required crossbar/quick-disconnect hardware may not all be in the baseplate carton. Missing pieces change the total price.

Example in practice

An owner keeping a crossbar-dependent setup compares 524480-4 with the cost of changing the bar ends and accessories to Direct-Connect. Buying 524480-5 just because it looks cleaner may prevent the existing equipment from connecting.

Complete the application

List the crossbar, quick-disconnect pieces, base pins and accessory approvals in the estimate. The bracket suffix is part of the application, not an optional detail.

Product instructions ↗

2025–2026 Hybrid

Roadmaster Crossbar-Style

524480-4

RM82VT

The Crossbar-Style alternative for a compatible Roadmaster crossbar system. It is a different connection choice from 524480-5.

Fitment & installation details

Useful when an existing approved bar or accessory calls for a crossbar. Include the required crossbar or quick-disconnect assembly in the equipment audit. Do not assume the baseplate box supplies every piece of the coach-to-truck connection.

Manufacturer manual finder
Roadmaster Direct-Connect · 524470-5Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

The established earlier-body application is the 2022–2024 Maverick 2.5L Hybrid. Roadmaster’s current earlier-year FitMaster entry also mentions the 2025 XL, while its 2025 entry lists 524480-5: resolve that catalog overlap against the actual front end before ordering for a 2025 XL.

What it does and who it suits

This Direct-Connect kit suits an earlier Hybrid and a compatible Roadmaster motorhome-mounted bar when the owner wants a removable-arm connection without a separate crossbar.

Pros — reasons to choose it

  • Simpler campsite handling than an otherwise equivalent crossbar arrangement.
  • Can pair with an existing serviceable Roadmaster-ended bar when its application and condition are suitable.

Cons — tradeoffs and limits

  • Does not provide the crossbar mounting points needed by StowMaster or some protective accessories.
  • Earlier-body photos and a general Maverick description do not prove a refreshed-body fit; the current 2025 XL overlap needs a specific answer.

Example in practice

A 2023 Hybrid owner retaining a Nighthawk 676 compares 524470-5 for a direct connection. Moving that hardware to a 2025 truck requires a new application decision rather than assuming all Mavericks share the same front structure.

Complete the application

Include any fascia trimming in the scope. Obtain new or replacement installation hardware exactly as the manufacturer directs when transferring a kit.

Product instructions ↗ · Manufacturer application / specifications ↗

2022–2024 Hybrid

Roadmaster Direct-Connect

524470-5

Manufacturer part number

Earlier-body Direct-Connect application. Compare this when building around a compatible Roadmaster bar for a 2022, 2023 or 2024 Hybrid.

Fitment & installation details

The 2025 front-end change requires a new fitment check; this is not an automatic carryover. Confirm fascia changes, cooling-system clearance and accessory restrictions in the current instructions.

Manufacturer PDF
Blue Ox · BX2913Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Blue Ox’s current catalog lists BX2913 for 2022–2024 Maverick HEV with adaptive cruise control and shutters. It is the earlier-body removable-tab application; BX2917 is the 2025–2026 listing.

What it does and who it suits

Compare this for an earlier Hybrid when you want Blue Ox tabs or already own an appropriate Blue Ox-ended tow bar. The vehicle-specific instructions matter more than an older online listing using a different Blue Ox part number.

Pros — reasons to choose it

  • Removable tabs improve everyday appearance.
  • A published Maverick application and BX8848 wiring listing make it easier to specify the truck-side parts by number.

Cons — tradeoffs and limits

  • Drilling, trimming and shutter changes are real installation tradeoffs. The pedestrian-alert speaker is removed for access and reinstalled.
  • A used kit labeled BX2690 needs Blue Ox’s application review; do not treat an older number as automatically identical to BX2913.

Example in practice

A 2024 Hybrid owner with an Alpha BX7390 can compare BX2913 against other systems while keeping the tow bar. That saving only holds if the bar, tabs, pins and mounting hardware are all suitable and complete.

Complete the application

Ask to see the applicable shutter/fascia pages before installation, and inspect that the removed speaker and electrical connections have been restored.

Product instructions ↗ · Manufacturer application / specifications ↗

2022–2024 HEV

Blue Ox

BX2913

Earlier listings may reference BX2690

The current Blue Ox catalog lists BX2913 for 2022–2024 HEV applications with adaptive cruise control and shutters.

Fitment & installation details

The BX2913 instructions require fascia work, drilling and trimming. They also describe removal of shutters and the pedestrian-alert speaker during access; the speaker is reinstalled. Read the actual instructions to understand which shutter components remain off. Verify any older BX2690 kit with Blue Ox before reuse.

Manufacturer PDF
Demco Tabless · 9519360Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Demco’s earlier Maverick application is 9519360, documented in TP29360. Keep it with the earlier-body Hybrid comparison; 9519366 is the separate refreshed-front-end part.

What it does and who it suits

This is a removable-tab route into an approved Demco connection. It is useful to compare when retaining a serviceable Demco bar or choosing one of Demco’s current motorhome-mounted models.

Pros — reasons to choose it

  • Removable connecting pieces reduce protrusion when the truck is unhitched.
  • The manual’s parts drawing makes missing braces, safety attachments and fasteners easier to identify before an installation begins.

Cons — tradeoffs and limits

  • Removing the tabs does not remove the permanently installed baseplate or undo fascia modifications.
  • A secondhand bracket with unknown collision history, missing braces or substituted bolts can erase any apparent purchase saving.

Example in practice

An owner moving a Dominator from an older towed car to a 2023 Maverick may reuse the approved bar, but still needs the Maverick-specific 9519360 mounting system and a fresh review of height and cable length.

Complete the application

Record the baseplate part number separately from the removable tab number. Inspect the complete kit against TP29360 instead of accepting a seller’s description of “Demco Maverick brackets.”

Product instructions ↗

2022–2024 Hybrid

Demco Tabless

9519360

DM77YV

Earlier Maverick Demco application. Keep this separate from the refreshed-front-end 9519366 kit when comparing quotes or used equipment.

Fitment & installation details

Match the part label, complete hardware list and latest manufacturer fitment to the VIN. Used or transferred baseplates need a condition and installation review; missing plates or substituted hardware can change the integrity of the mount.

Manufacturer fitment catalog
etrailer Invisible · e64FVClick for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

The earlier-body etrailer Maverick entry is e64FV, with LIT-00692 instructions. Keep it distinct from refreshed-body e96GV when researching 2022–2024 Hybrid equipment.

What it does and who it suits

A removable-arm alternative for owners comparing an etrailer tow-bar package or an expressly approved adapted connection. Evaluate the complete coach-to-truck arrangement rather than assuming every two-pin interface is the same.

Pros — reasons to choose it

  • Arms can be removed for daily driving.
  • Useful as a complete-package comparison when the quote explicitly includes the correct bar ends and hardware.

Cons — tradeoffs and limits

  • Adapter choice can add hardware, length and cost; that belongs in the comparison before purchase.
  • An installed photo on a different Maverick generation cannot establish mounting or cooling-system clearance on your truck.

Example in practice

A 2022 Hybrid owner pricing an SD bar and e64FV should compare that installed total with a Roadmaster or Blue Ox package that includes equivalent brakes, lights and charging.

Complete the application

Check that the scope includes the socket location, breakaway switch and safety-cable routing. Those small installation decisions affect how convenient the system is every trip.

Product instructions ↗

2022–2024 Hybrid

etrailer Invisible

e64FV

Brand catalog part number

Earlier-body removable-arm option. This is the earlier application; e96GV belongs to the refreshed front-end comparison.

Fitment & installation details

Inspect the exact tow-bar connection and approved adapters before buying. Quote the baseplate, installation hardware, safety connections, electrical socket and breakaway mounting as a complete package.

Roadmaster Crossbar-Style · 524470-4Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

The earlier-body Crossbar-Style Roadmaster kit is 524470-4. It belongs in the 2022–2024 Hybrid comparison and serves a different interface from Direct-Connect 524470-5.

What it does and who it suits

Consider it when preserving an approved crossbar-style system is more useful than converting the connection. This can matter for an existing bar or an accessory that mounts to the crossbar.

Pros — reasons to choose it

  • Can retain compatible equipment the owner already understands.
  • Provides the required crossbar-style mounting layout where a Direct-Connect kit would not.

Cons — tradeoffs and limits

  • More pieces to attach and store during campsite changes.
  • A used bar plus an incomplete crossbar can cost more to make serviceable than expected; inspect all connecting pieces before calling reuse a saving.

Example in practice

A 2024 owner with a complete approved Roadmaster crossbar system may reasonably choose -4. An owner starting from scratch should compare the same installation with -5 and decide whether any crossbar-dependent accessory is actually needed.

Complete the application

Inventory the crossbar, quick-disconnect components, pins, retainers and approved accessories. Compare the arm-removed photos as well as the fully connected appearance.

Product instructions ↗

2022–2024 Hybrid

Roadmaster Crossbar-Style

524470-4

RM37RR

Earlier-body Crossbar-Style choice for a compatible Roadmaster crossbar setup, including some existing equipment combinations.

Fitment & installation details

Compare the visible connection and accessory needs with the Direct-Connect version. The suffix matters: -4 and -5 are not interchangeable descriptions. Confirm the complete crossbar assembly and any approved adapters in the estimate.

Manufacturer PDF

Previous 15Next 15 baseplates
Fitment checks and installation notesRead before choosing a baseplateTap to close

Installed appearance is only part of the decision.

Installed appearance is only part of the decision.Removable arms can leave a less noticeable front end when the truck is driven normally. The permanent structure, electrical socket and breakaway switch remain. Photos are application references; trim, mounting position and accessories can change the final appearance.

What we check before ordering

What we verify before ordering

VIN, model year, Hybrid drivetrain, trim, adaptive cruise/radar, active shutters, front fascia, collision history and any aftermarket accessories. We also match the bracket to the actual tow-bar ends.

What can change during installation

Fascia removal, grille trimming, drilling, shutter modifications and sensor clearance are kit-specific. We explain the applicable changes in the estimate. “Custom fit” does not mean every installation is reversible without visible changes.

Send the VIN and a front photo. We will identify the correct application and compare the complete installed options.

Plan my installation

About this topic

Choose the correct generation first. Manufacturer numbers are shown prominently; alternate catalog references help identify the same item in an existing quote. Tap an installed photo to enlarge it.

Choose another section ↑
Choose another topicNext section →

Equipment / Tow Bars

The right bar is a system decision.

Tap an option to open it. Tap it again to close it.

Choose for the way you travel

Once the truck, coach and connection are approved, compare the features you will use at every stop. Capacity is one requirement; lifting the bar, reaching the release, managing cables and storing the arms are daily ownership decisions.

Frequent lifting and removal

Compare complete product weight. Demco lists Dominator at 30 lb, Commander 2 at 41 lb and Excali-Bar 3 at 46 lb. Blue Ox lists Alpha BX7390 at 40 lb; CURT lists Rambler 70015 at 38 lb. Try the complete assembly rather than judging by aluminum/steel labels alone.

Low-light hookup

Nighthawk’s illuminated arms distinguish it from a capacity-only choice. The benefit is visibility around the connection; you still need to test the truck’s rear signals and inspect every retaining pin.

Keeping existing equipment

Start with model, receiver shank, installed ends, condition and recall status. Nighthawk 676 and 677, Falcon 3HD 622 and 627, and Sterling 576 and 586 deliberately have different end configurations. Reusing a sound bar can make sense; buying the wrong baseplate to match a worn-out bar may not.

Future vehicles and capacity

Falcon 3HD, Avail, Apollo, Excali-Bar 3, XHD and Seeker offer different higher ratings. Evaluate the future motorhome/vehicle combination too. Where the bar maker specifies sizing by the towed vehicle’s GVWR, meet that requirement as well as checking actual loaded weight and coach limits.

Demco weight comparison · Alpha specifications · Rambler specifications

About tow bars: how to choose a complete connectionClick for the full explanation and two examplesTap to close

Compare rated capacity, handling weight, attachment ends, receiver size and hookup convenience. These are equipment options, not blanket approval of every bar-and-baseplate combination.

A tow bar links the motorhome’s receiver to the Maverick’s baseplate. The baseplate attaches to the truck; the bar connects the two vehicles. Neither part replaces Ford’s Neutral Tow procedure, supplemental braking, the breakaway system, safety cables, lighting or a suitable 12-volt power plan. Choose those pieces as one complete setup.

Start with the truck and motorhome you actually have

Confirm that Ford permits your exact Maverick to be towed four wheels down, then choose its model-year baseplate. Record the motorhome’s permitted towing weight, receiver size and ratings, and the truck’s loaded weight. Only then narrow the tow-bar choices by attachment style, capacity and the amount of weight you can comfortably lift and store.

Think about the routine at every campsite

Compare how the arms extend and lock, how the release handles work, where the bar folds for storage and what cables or adapters are included. A nonbinding release can make disconnecting easier when the connection is under load. You still need a suitable parking position and the manufacturer’s release procedure. It does not permit backing up with the truck attached.

Example 1: starting with no equipment

An owner of an eligible 2025 Maverick Hybrid starts with the refreshed-front-end baseplate applications. After the coach’s limits and receiver are checked, the owner compares compatible tow bars and plans the brakes, lights and charging together. Buying the highest-rated bar first would leave those other decisions unresolved.

Example 2: keeping an existing tow bar

An owner changing from another towed vehicle to a 2024 Maverick records the bar’s exact model, serial number and installed attachment ends. The installer checks condition, recalls, the correct earlier-year baseplate and any approved adapter. A familiar brand name or a pin that appears to fit is not enough to establish the combination.

Open a product below for its photos, comparison details and PDF instructions. Then use the four expandable checks for capacity, connections, height and used equipment before making the final selection.

See the tow-bar connection explainedTap to readTap to close
Roadmaster Nighthawk tow bar with arms, connection ends, safety cables and electrical cord
Roadmaster manufacturer product image · Nighthawk reference.
Know the connection

One bar. Several decisions.

The arms and attachment ends connect to the baseplate. The receiver shank connects to the motorhome. Safety cables and the electrical cord serve separate functions, even when routed along the bar.

Shown: a Roadmaster Nighthawk. Compare this and the other options in the table below.

See tow-bar product photosTap to readTap to close
Roadmaster Nighthawk · 676 / 677Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Nighthawk 676 has Roadmaster ends; 677 has Blue Ox ends. For Maverick applications, compare 676 with the matching Roadmaster mounting system and 677 with BX2913 or BX2917. Both are 8,000-lb bars; vehicle eligibility and the coach’s lower limits still govern.

What it does and who it suits

Its distinguishing feature is lighting along the arms, combined with a nonbinding release and organized cable routing. It is worth comparing when visibility around the connection and frequent campsite hookups matter to you.

Pros — reasons to choose it

  • Illuminated arms make the connection easier to see in low light.
  • Nonbinding release and routed cables can simplify the routine around the back of the coach.

Cons — tradeoffs and limits

  • The lighting is an extra electrical feature to connect and maintain; it does not replace the truck’s rear towing lights.
  • Paying for convenience features adds no usable capacity if the coach’s receiver or combined-weight allowance is already the limiting factor.

Example in practice

For an owner arriving after dusk, seeing the arms and cable path can be useful. That owner still walks around the truck to test the brake and turn lights; illumination on the bar cannot perform that check.

Complete the application

Check the exact end version, cord/socket contents and Roadmaster recall applicability by serial number. Confirm any applicable recall remedy before use.

Product instructions ↗

Roadmaster Nighthawk tow bar with arms, connection ends, safety cables and electrical cord
Roadmaster manufacturer product image · Nighthawk reference.
Part / version
676 / 677
Rated capacity
8,000 lb
What to compare
676: Roadmaster ends; 677: Blue Ox ends. LED illumination and nonbinding design. Verify the selected version and current recall status.

Owner manual PDF

Roadmaster Falcon 3HD · 622 / 627Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Falcon 3HD 622 uses Roadmaster ends and 627 uses Blue Ox ends; both are rated 10,000 lb. This is a different model from the older Falcon 2 or Falcon All-Terrain, so use the 3HD manual and label.

What it does and who it suits

Consider this when a current Roadmaster bar with greater rated capacity is useful, particularly if future approved towed vehicles are part of your plan. The bar’s number is only one component limit.

Pros — reasons to choose it

  • Offers a choice of Roadmaster or Blue Ox attachment ends within the same bar family.
  • Its 10,000-lb rating provides more bar capacity than the 8,000-lb Roadmaster options listed here.

Cons — tradeoffs and limits

  • Higher rating alone does not make a Maverick setup more suitable, easier to lift or better at braking.
  • Do not assume the electrical cord, baseplate, brake or every accessory comes with the bar. Compare package contents line by line.

Example in practice

An owner considering a future heavier towed vehicle can include 3HD in the comparison, then check whether the motorhome could tow that future vehicle at all. A 5,000-lb receiver would remain a 5,000-lb limit.

Complete the application

Verify 622 versus 627 before ordering, inspect operating and stowing clearance, and check the current Roadmaster recall by model and serial number.

Product instructions ↗

Roadmaster Falcon 3HD 622 · product referenceEnlarge photo
Roadmaster Falcon 3HD 622 · product reference. Photo: etrailer reference; not a Stellar customer installation.
Part / version
622 / 627
Rated capacity
10,000 lb
What to compare
622: Roadmaster ends; 627: Blue Ox ends. Current heavy-duty option; check the manufacturer’s recall notice before use.

Owner manual PDF

Roadmaster Sterling · 576 / 586Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Sterling 576 is the Roadmaster-ended version; 586 is the Blue Ox-ended version. Both are in the 8,000-lb Sterling All-Terrain family. Use the actual serial number when identifying parts on an older bar.

What it does and who it suits

An aluminum-bodied Roadmaster option to compare for handling and nonbinding release. It is also a common reuse decision: a good existing bar may remain useful if its connection, condition and service status are suitable.

Pros — reasons to choose it

  • Nonbinding release is useful when normal campsite loading makes disconnecting awkward.
  • Aluminum construction and cable management are practical features to compare by handling the complete bar, not by looking only at its rating.

Cons — tradeoffs and limits

  • An older Sterling may need service or different attachment components; a familiar product name does not establish its condition.
  • A used package may be missing the electrical cord, safety components or correct connection hardware.

Example in practice

A motorhome owner who already has a Sterling 586 can investigate a Blue Ox Maverick baseplate before buying another tow bar. A 576 requires the Roadmaster connection or an expressly approved conversion.

Complete the application

Review wear, latch action, pins, cable condition and the current recall notice. Match replacement parts to the serial-number range in the manufacturer documentation.

Product instructions ↗

Roadmaster Sterling 576 · product referenceEnlarge photo
Roadmaster Sterling 576 · product reference. Photo: etrailer reference; not a Stellar customer installation.
Part / version
576 / 586
Rated capacity
8,000 lb
What to compare
Identify the attachment ends and exact version. An existing Sterling needs the same wear and recall review as a new-system selection.

Owner manual PDF

Blue Ox Alpha · BX7390Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Alpha BX7390 is an 8,500-lb steel bar with a 2-inch receiver shank and Blue Ox attachment style. Compare it with BX2913 for 2022–2024 HEV or BX2917 for 2025–2026 HEV.

What it does and who it suits

A straightforward Blue Ox motorhome-mounted choice for owners who want self-aligning arms and a nonbinding release without selecting the higher-capacity Avail or Apollo solely for the larger number.

Pros — reasons to choose it

  • Auto-locking arms and nonbinding latches support a repeatable hookup routine.
  • Blue Ox lists safety cables as included, which is useful when comparing otherwise incomplete packages.

Cons — tradeoffs and limits

  • Blue Ox lists a 40-lb product weight: try lifting and stowing it if handling is a priority.
  • It has a 2-inch shank; an owner with a different receiver size must plan the manufacturer-approved receiver arrangement.

Example in practice

A 2024 Hybrid owner with a 2-inch coach receiver can compare Alpha plus BX2913 against an Avail package. If both satisfy every rating, handling, release action and total package cost may matter more than unused capacity.

Complete the application

Check that the box contains the specified cables and connecting hardware. Electrical lighting, charging and supplemental braking remain separate decisions.

Product instructions ↗ · Manufacturer application / specifications ↗

Blue Ox Alpha BX7390 · product referenceEnlarge photo
Blue Ox Alpha BX7390 · product reference. Photo: Blue Ox reference; not a Stellar customer installation.
Part / version
BX7390
Rated capacity
8,500 lb
What to compare
Current Alpha model, 2-inch receiver. Nonbinding design; confirm baseplate interface and supplied safety cables.
Blue Ox Avail · BX7421 / BX7426Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Avail BX7421 fits a 2-inch receiver; BX7426 fits a 2½-inch receiver. Both listed versions are rated 10,000 lb and use the Blue Ox connection appropriate to BX2913 or BX2917.

What it does and who it suits

The receiver-size choice is a major reason to compare the two versions. Nonbinding operation and the available capacity can suit an owner retaining a Blue Ox baseplate system or planning a different approved towed vehicle later.

Pros — reasons to choose it

  • Two shank sizes allow a deliberate match to the coach instead of assuming every Avail has the same receiver fit.
  • Nonbinding latches reduce one source of frustration during normal unhooking.

Cons — tradeoffs and limits

  • Ordering BX7426 for a 2-inch receiver creates a physical mismatch even though the truck-side ends look right.
  • Extra tow-bar capacity does not increase receiver, coach or baseplate-system limits.

Example in practice

A buyer comparing two used Avail bars should photograph the model label and measure the shank. An older BX7420 is a separate model, not proof of the specifications listed for BX7421 or BX7426.

Complete the application

Use the manual for the exact receiver version. Confirm the connection parts, cable length and maintenance history before treating a used bar as ready to travel.

Product instructions ↗

Blue Ox Avail BX7421 · product referenceEnlarge photo
Blue Ox Avail BX7421 · product reference. Photo: Blue Ox reference; not a Stellar customer installation.
Part / version
BX7421 / BX7426
Rated capacity
10,000 lb
What to compare
BX7421: 2-inch receiver. BX7426: 2½-inch receiver. Do not confuse the receiver size with the tow-bar end style.
Blue Ox Apollo · BX7475 / BX7470Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Apollo BX7475 is rated 12,500 lb with a 2-inch receiver; BX7470 is rated 15,000 lb with a 2½-inch receiver. These versions use the Blue Ox connection, with the appropriate Maverick baseplate and attachment spacing.

What it does and who it suits

This is the high-capacity Blue Ox comparison, most relevant when the owner’s wider towing plans justify it. A Maverick-only purchase should still compare handling, price and daily use against Alpha or Avail.

Pros — reasons to choose it

  • A choice of high ratings and receiver sizes for different approved coach/vehicle combinations.
  • Allows an owner to evaluate a future heavier vehicle without immediately ruling out the tow bar’s own capacity.

Cons — tradeoffs and limits

  • Large capacity can be unused on a Maverick and cannot compensate for a lower-rated motorhome.
  • The 2½-inch version cannot fit a 2-inch opening, and an adapter is not automatically an approved solution.

Example in practice

If the motorhome can tow only 5,000 lb, replacing an adequate bar with a 15,000-lb Apollo does not make the coach capable of towing a 7,000-lb vehicle.

Complete the application

Compare the complete bar’s handling and the exact manual’s leveling limits. Keep the BX7475 and BX7470 instructions separate when discussing specifications.

Product instructions ↗

Blue Ox Apollo BX7475 · product referenceEnlarge photo
Blue Ox Apollo BX7475 · product reference. Photo: etrailer reference; not a Stellar customer installation.
Part / version
BX7475 / BX7470
Rated capacity
12,500 / 15,000 lb
What to compare
BX7475: 2-inch receiver, 12,500 lb rating. BX7470: 2½-inch receiver, 15,000 lb rating. Extra bar capacity does not increase the motorhome’s permitted towing load.
Demco Commander 2 · 9511012Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Commander 2 is Demco’s 6,000-lb steel model for a 2-inch coach receiver. The standard Demco connection belongs with the approved Demco tab arrangement, such as the corresponding Maverick 9519360 or 9519366 application.

What it does and who it suits

Demco positions it as the entry-level choice. For an eligible Maverick within all component ratings, the decision against Dominator is often purchase cost versus the weight you lift.

Pros — reasons to choose it

  • Self-supporting, independently moving arms help with hookup.
  • Easy Trigger Release, safety cables and a built-in 1½-inch offset are included features in Demco’s comparison.

Cons — tradeoffs and limits

  • Demco lists 41 lb, versus 30 lb for Dominator. That difference matters if you remove the bar from the receiver frequently.
  • The 6,000-lb rating leaves less capacity for a future heavier vehicle than Demco’s other two listed bars.

Example in practice

An occasional traveler who leaves the bar stored on the motorhome may accept the heavier steel unit. Someone lifting it into storage after every trip may value the Dominator’s lower listed weight more.

Complete the application

Use the actual bar’s height-adjustment instructions; built-in adjustment does not guarantee that no additional approved rise/drop is needed.

Product instructions ↗ · Manufacturer application / specifications ↗

Demco Commander 2 · 9511012Enlarge photo
Demco Commander 2 · 9511012
Image: Demco · manufacturer reference
Part / version
9511012
Rated capacity
6,000 lb
What to compare
Steel bar; a practical Demco-system comparison. Current catalog includes safety cables and self-supporting arms.

Owner manual PDF

Demco Dominator · 9511008Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Dominator is Demco’s 7,500-lb aluminum model for a 2-inch receiver and the appropriate Demco baseplate connection. Use the Maverick mounting application for the correct body generation.

What it does and who it suits

Its clearest distinction is handling weight. Demco lists 30 lb, compared with Commander 2 at 41 lb and Excali-Bar 3 at 46 lb. This can matter more than surplus towing capacity for a Maverick owner.

Pros — reasons to choose it

  • The lowest listed physical weight of these three Demco options.
  • Independent, self-supporting arms and Easy Trigger Release help organize the hookup and release routine.

Cons — tradeoffs and limits

  • The aluminum option may cost more than the entry-level Commander package; compare current installed quotes.
  • The 7,500-lb rating is lower than Excali-Bar 3’s; future vehicle plans still need a fresh capacity review.

Example in practice

An owner who has difficulty lifting a steel bar can compare the complete Dominator in person. The 11-lb difference from Commander 2 is a tangible handling consideration, not a claim that the truck will tow differently.

Complete the application

Confirm the supplied connecting ends, cables and approved leveling arrangement. A lighter bar still requires the same inspection and arm-lock verification.

Product instructions ↗ · Manufacturer application / specifications ↗

Demco Dominator · 9511008Enlarge photo
Demco Dominator · 9511008
Image: Demco · manufacturer reference
Part / version
9511008
Rated capacity
7,500 lb
What to compare
Lighter 30 lb bar in the current Demco catalog. Compare handling weight as well as capacity.

Owner manual PDF

Demco Excali-Bar 3 · 9511013Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Excali-Bar 3 is rated 10,500 lb and mounts in a 2-inch receiver. Match its Demco-style connection to the approved Maverick baseplate or expressly listed adapter.

What it does and who it suits

This is Demco’s higher-capacity steel option. It is most useful to compare when a broader towing plan calls for that capacity and the motorhome can support it.

Pros — reasons to choose it

  • Highest rated capacity of the three Demco bars shown here.
  • Retains independent arms, nonbinding release and the Demco adjustable connection layout.

Cons — tradeoffs and limits

  • Demco lists a 46-lb physical weight, 16 lb more than Dominator; handle the assembled bar before choosing by rating alone.
  • A Maverick setup may gain no usable towing allowance when the receiver or coach is the limiting component.

Example in practice

An owner who keeps the bar on the coach and anticipates another approved vehicle might prefer the capacity. An owner removing it after every outing may instead favor Dominator’s lower weight.

Complete the application

Use the Excali-Bar 3 manual TB20061 for hookup and leveling. Do not substitute instructions for an earlier Excali-Bar with a similar name.

Product instructions ↗ · Manufacturer application / specifications ↗

Demco Excali-Bar 3 9511013 · product referenceEnlarge photo
Demco Excali-Bar 3 9511013 · product reference. Photo: etrailer reference; not a Stellar customer installation.
Part / version
9511013
Rated capacity
10,500 lb
What to compare
Higher-capacity Demco option. Includes safety cables in the current manufacturer catalog.
etrailer SD · e34ZRClick for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

etrailer SD e34ZR is a 6,000-lb, 2-inch-receiver bar supplied for etrailer and Demco baseplates. The product page lists other connection configurations separately: e47ZR for Blue Ox, e44ZR for Roadmaster Crossbar-Style and e74ZR for Roadmaster Direct-Connect.

What it does and who it suits

This is a practical comparison for an etrailer or Demco Maverick baseplate package. Self-supporting arms and integrated safety cables address daily hookup organization.

Pros — reasons to choose it

  • Arms support their own weight while you connect them.
  • Built-in rise/drop and head adjustment offer useful leveling options within the instructions.

Cons — tradeoffs and limits

  • The 6,000-lb rating provides less future-vehicle margin than XHD.
  • The product page warns that rise/drop use can require safety-cable extensions; included cables do not guarantee adequate reach on every setup.

Example in practice

A buyer with BX2913 should not order e34ZR simply because it is an etrailer bar. The Blue Ox configuration listed by the brand is e47ZR; that distinction belongs in the quote.

Complete the application

Specify the full bar configuration, cable reach and approved height setup. Compare the current supplied ends if evaluating a used or modified bar.

Product instructions ↗ · Manufacturer application / specifications ↗

etrailer SD e34ZR · product referenceEnlarge photo
etrailer SD e34ZR · product reference. Photo: etrailer reference; not a Stellar customer installation.
Part / version
e34ZR
Rated capacity
6,000 lb
What to compare
RV-mounted, 2-inch receiver, nonbinding arms and integrated safety cables. Verify end style and rise/drop limitations.
etrailer XHD · e94ZRClick for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

etrailer XHD e94ZR is the 10,500-lb, 2-inch-receiver configuration for etrailer/Demco baseplates. Its product page lists e67ZR for Blue Ox, e64ZR for Roadmaster Crossbar-Style and e84ZR for Roadmaster Direct-Connect. These are different from the SD family’s configuration numbers.

What it does and who it suits

Compare XHD with SD when higher bar capacity is useful, while evaluating the handling and storage of the complete assembly. Its self-supporting arms and integrated cables organize the connection.

Pros — reasons to choose it

  • Higher rated bar capacity than the 6,000-lb SD.
  • Self-supporting arms reduce the need to hold both arms up during hookup.

Cons — tradeoffs and limits

  • Higher capacity does not eliminate height, cable-reach or coach-rating limitations.
  • A nominal tow-bar price can omit the specific connection conversion needed by a different brand of baseplate.

Example in practice

An owner using an etrailer Maverick baseplate can compare SD and XHD as complete packages. If both satisfy the application, the decision should include handling and future plans rather than a larger rating alone.

Complete the application

Have the seller identify the exact approved XHD connection in writing and include any required cable extensions in the parts list.

Product instructions ↗ · Manufacturer application / specifications ↗

etrailer XHD e94ZR · product referenceEnlarge photo
etrailer XHD e94ZR · product reference. Photo: etrailer reference; not a Stellar customer installation.
Part / version
e94ZR
Rated capacity
10,500 lb
What to compare
Higher-capacity RV-mounted alternative with self-supporting arms and integrated safety cables. Confirm the exact ends and operating-angle instructions.
CURT Rambler · 70015Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Rambler 70015 is a 7,500-lb steel bar with a 2-inch shank. Its manual illustrates a three-lug connection secured with the supplied ½-inch pin; an arbitrary pin fit is not approval for another brand’s baseplate.

What it does and who it suits

Compare it when handling weight, nonbinding release and storage positions matter. CURT lists a 38-lb product weight and three stowing positions.

Pros — reasons to choose it

  • Nonbinding latches and automatic locking arms support routine hookup and release.
  • Side or centered stowing can help accommodate equipment at the rear of the coach.

Cons — tradeoffs and limits

  • An approved connection to the chosen Maverick baseplate must be part of the order; a “universal part” label is not a vehicle-specific baseplate approval.
  • The manual permits one approved leveling connection, not a stack of a leveling adapter plus an extension.

Example in practice

A coach with rear-mounted accessories may benefit from a different stowing position. Check the actual folded bar against the spare tire, ladder and storage-door swing before purchase.

Complete the application

Read the 70015 manual’s height diagram and arm-lock checks. The lower-priced CURT 19745 universal coupler bar is a different design and is not a substitute specification.

Product instructions ↗ · Manufacturer application / specifications ↗

CURT Rambler 70015 · product referenceEnlarge photo
CURT Rambler 70015 · product reference. Photo: CURT reference; not a Stellar customer installation.
Part / version
70015
Rated capacity
7,500 lb
What to compare
2-inch shank. Use the manufacturer-approved baseplate connection; the universal 19745 bar is a different product.
CURT Seeker · 70012Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Seeker 70012 is CURT’s 10,000-lb, 2-inch-shank bar. The manual shows the supplied ½-inch-pin lug connection and identifies the locking-collar position for towing.

What it does and who it suits

Consider it as CURT’s higher-capacity comparison with Rambler. The useful differences include capacity, release/locking operation and how the bar stows on your motorhome.

Pros — reasons to choose it

  • 10,000-lb bar rating for an otherwise approved towing combination.
  • Three storage positions and protected arms provide practical features to compare on the coach.

Cons — tradeoffs and limits

  • A higher rating does not make its ends fit every Maverick baseplate. The approved connection still needs to be specified.
  • The manual prohibits combining a leveling adapter and receiver extension; rear accessory clearance cannot be solved by unrestricted adapter stacking.

Example in practice

If a rear spare tire conflicts with the stowed bar, first evaluate the listed storage positions. Adding receiver extensions without checking the instructions can create a new limit instead of solving the installation.

Complete the application

Have the installer demonstrate the collar’s locked state and both supplied safety cables. Compare the complete connection price with Rambler, not only the bar’s advertised capacity.

Product instructions ↗ · Manufacturer application / specifications ↗

CURT Seeker 70012 · product referenceEnlarge photo
CURT Seeker 70012 · product reference. Photo: CURT reference; not a Stellar customer installation.
Part / version
70012
Rated capacity
10,000 lb
What to compare
2-inch shank. Compare exact connection hardware, clearance and included accessories before treating it as a package.
NSA Ready Brute Elite II · RB-9050-2Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Ready Brute Elite II combines an 8,000-lb bar with mechanical surge braking. NSA sells different clevis options, including Blue Ox, Demco Classic and Roadmaster hole-size versions; choose the one approved for the actual baseplate.

What it does and who it suits

As the towed vehicle pushes against the slowing coach, the surge mechanism pulls an installed cable that applies the truck’s brake pedal. It is a different operating approach from a portable electric pedal actuator.

Pros — reasons to choose it

  • Combines the tow-bar and normal supplemental-braking mechanism in one system.
  • Removes the need to position a portable brake box in the driver footwell at every campsite.

Cons — tradeoffs and limits

  • Cable routing, free movement and adjustment are essential installation work; the bar by itself does not complete the brake installation.
  • Breakaway, monitoring and the exact Maverick active-assist application must be addressed explicitly. Mechanical operation is not a reason to ignore the Hybrid’s pedal response.

Example in practice

An owner comparing Elite II with a separate tow bar and DUO should compare complete installed systems: include the NSA vehicle cable, breakaway and monitor before comparing totals.

Complete the application

Do not confuse Ready Brute II with Ready Brute Elite II: NSA states the non-Elite tow bar lacks the integrated surge brake. Have the installer demonstrate full pedal release.

Product instructions ↗ · Manufacturer application / specifications ↗

NSA Ready Brute Elite II · RB-9050-2Enlarge photo
NSA Ready Brute Elite II · RB-9050-2
Image: NSA · manufacturer reference
Part / version
RB-9050-2
Rated capacity
8,000 lb
What to compare
Tow bar with integrated mechanical surge braking. Confirm the correct clevis ends, vehicle cable installation and separate breakaway requirements.

Owner manual PDF

Previous 15Next 15 tow bars
Current Roadmaster recall check · NHTSA 26E069Read this important informationTap to close
Current Roadmaster recall check · NHTSA 26E069Roadmaster’s October 20, 2026 notice identifies certain tow-bar models and serial ranges involving T-bolt roll pins. Check the model, serial and inspection instructions before using an affected bar. A missing, damaged or improperly seated pin needs the manufacturer’s resolution before towing. Read the official notice and model/serial table.
Capacity, adapters, height and used equipmentTap to readTap to close

Capacity: the smallest limit controls

Compare the loaded Maverick weight with the motorhome’s permitted towing capacity, GCWR and receiver label, then the bar, high-low adapter and safety cables. A 10,000 lb bar does not turn a 5,000 lb coach hitch into a 10,000 lb hitch.

Click for more info & examplesRead the explanation and two practical examplesClose the expanded explanation

Use the Maverick’s actual travel weight, including installed equipment and anything carried in it. Compare that weight with every applicable limit: the motorhome’s towing rating, its available combined-weight allowance, the receiver, tow bar, adapters, baseplate system and safety cables. The lowest applicable limit is the ceiling; satisfying it still does not establish fitment or braking approval.

GCWR means gross combined weight rating: the maximum permitted loaded weight of the motorhome and what it tows. Subtracting the loaded coach weight from GCWR gives one weight allowance to check. The receiver label or motorhome instructions may impose a lower limit.

Example 1 — the receiver is the limit: assume a truck weighs 4,100 lb ready to tow, the receiver is rated for 5,000 lb, the bar for 10,000 lb and every other relevant limit is at least 5,000 lb. The bar does not raise the combination’s 5,000 lb ceiling. These are illustrative figures, not a Maverick weight specification.

Example 2 — the loaded coach changes the answer: a hypothetical 26,000 lb GCWR minus a 22,200 lb loaded motorhome leaves 3,800 lb. That would be insufficient for the same 4,100 lb truck, even with a 5,000 lb receiver. A larger tow bar would not resolve that limit.

Review the complete setup and use the coach manufacturer’s ratings and actual scale weights for your own calculation.

Connection: inspect both ends

Receiver size, baseplate tabs, clevis/ear style and crossbar requirements are separate choices. Use only manufacturer-approved adapters. Account for the adapter’s rating, extra length and effects on turning and height.

Click for more info & examplesRead the explanation and two practical examplesClose the expanded explanation

There are two separate interfaces to match. At the motorhome, check the receiver opening, shank size, pin and any rise/drop adapter. At the truck, match the tow-bar ends to the removable baseplate arms or required crossbar. The same tow-bar family may be sold with different ends, so compare full part numbers and the hardware actually installed.

An approved adapter must explicitly cover the combination. Check its capacity, fastening instructions, additional length and clearance while turning. Do not assume that a reducer sleeve, receiver extension and baseplate adapter are interchangeable parts: they solve different connection problems.

Example 1 — two versions of one bar: the Roadmaster Falcon 3HD manual identifies 622 and 627, with Blue Ox ears on 627. An owner needs to match those ends to the selected baseplate, not select solely by the Falcon name or 10,000 lb rating.

Example 2 — a different receiver size: an existing 2.5-inch tow-bar shank cannot slide into a 2-inch motorhome receiver. Confirm whether the manufacturer offers an approved replacement shank or a different bar configuration. Do not modify the receiver or improvise hardware to make it fit.

Falcon 3HD manual and connection illustrations (PDF)

Height: measure the actual vehicles

Measure on level ground in travel condition. The tow-bar manual defines its permitted operating angle and any rise/drop limits. Use an appropriately rated adapter only when needed; never substitute a generic universal “three-inch rule” for the selected bar’s instructions.

Click for more info & examplesRead the explanation and two practical examplesClose the expanded explanation

Park the motorhome and Maverick on the same level surface, loaded for travel. Set the coach’s suspension to its normal travel condition. Measure from the ground to the centers of the connection points specified in the selected tow-bar manual. Use that manual’s diagram because some bars have an adjustable head or built-in rise/drop that changes the measurement.

Compare the difference with the permitted range for that exact bar. If correction is needed, select an approved, adequately rated rise/drop arrangement and remeasure the finished connection. Also check ground clearance, turning clearance and enough slack for the safety cables, electrical cord and brake connection without letting them drag.

Example 1 — measuring a difference: a receiver center at 21 inches and the specified baseplate connection center at 16 inches have a 5-inch difference. That measurement starts the selection process; it does not by itself tell you which adapter is approved or whether the bar can operate at that angle.

Example 2 — why the exact manual matters: the Blue Ox Apollo BX7475 manual recommends the hitch receiver be within 3 inches above or below the baseplate tabs. Use that limit for the covered Apollo setup; check the appropriate Demco, CURT, Roadmaster or other manual for a different bar.

Apollo BX7475 height and connection guidance (PDF)

Used equipment: verify more than the label

Inspect arms, latches, joints, pins, cables, boots, mounting hardware and evidence of impact or binding. Check recall applicability and service requirements. Older Falcon All-Terrain, Avail BX7420 or other legacy versions should be evaluated by their own model label.

Click for more info & examplesRead the explanation and two practical examplesClose the expanded explanation

Record the manufacturer, complete model number and serial number before evaluating a used bar. Obtain the correct manual and ask about its service, storage and accident history. A current model’s rating or service instructions may differ from an older version that looks similar.

Inspect the arms, pivots, locking mechanisms, pins and retainers, attachment ends, boots and safety cables using the maker’s inspection procedure. Look for cracks, distortion, unusual looseness, damaged threads, corrosion or missing components. Appearance alone cannot establish condition: an impact or overload may leave damage that is difficult to see.

Example 1 — similar name, different equipment: a used Avail labeled BX7420 should be evaluated using its own identification and manual. Do not apply the details for the BX7421 / BX7426 choices on this page just because all are called Avail.

Example 2 — an arm will not lock: if one arm does not lock as its manual requires, or a pin or cable is damaged, stop the setup and obtain the manufacturer’s inspection or repair guidance. Replacing a visible clip alone does not demonstrate that the rest of the bar is fit for use.

Roadmaster tow-bar inspection instructions (PDF) · Roadmaster recall model and serial-number check

Do not back up with the Maverick attached.Read this important informationTap to close
Do not back up with the Maverick attached.Disconnect before backing or when the combination cannot complete a turn. A nonbinding latch helps release a loaded connection; it does not make reverse towing safe.

Have equipment already? We can check the combination before quoting.

Plan my installation
Choose another section ↑
Choose another topicNext section →

Equipment / Braking

Choose braking for the coach and the Hybrid.

Tap an option to open it. Tap it again to close it.

Start with the Maverick’s active brakes and the coach’s brake type

Roadmaster identifies the Maverick Hybrid as having the equivalent of full-time active brake assist. A small pedal force can produce substantial braking even when the truck is configured for towing. The supplemental brake must be designed and adjusted for that behavior.

Portable: equipment you position each trip

Patriot BRK2022: use the manufacturer’s Hybrid mode. RVibrake 4 52202: use its Active assist configuration and setup procedure. Their advantage is transferability; the tradeoff is repeated positioning, calibration and storage. Both still need the proper breakaway and 12V installation.

Installed behind a hydraulic-brake coach

Stay-IN-Play DUO: Demco’s current manual identifies additional regulator 6492 for the Maverick. Its initial installation is more involved, but daily equipment handling is reduced. Do not omit the regulator and adjustment from the quote.

Installed behind an air-brake coach

Air Force One: designed for the coach’s air-brake system. BrakeMaster 9160: a different air-coach option requiring the Maverick active-brake reducer and mounting components. Identify the coach chassis and any factory air connection before specifying either package.

Products that are not automatic transfers

Even Brake 9400 is excluded for active brakes by its manual, so it is shown below as an existing-equipment warning, not a Maverick recommendation. Brake Buddy Select 3 remains unconfirmed here until its exact manufacturer application and settings are established. A product’s presence in this guide does not mean every listed brake is suitable.

Example: changing coaches changes the brake decision

An owner moving from a hydraulic-brake motorhome to an air-brake coach should re-evaluate a DUO installation against an air-coach system. Keeping the same Maverick and tow bar does not make the two coach brake systems equivalent.

What a completed installation demonstrates: normal braking, complete pedal release, breakaway operation, accurate in-coach indication, and the reset procedure after Ford’s required stops. Readers should leave knowing which part does each job and which instructions govern their actual setup.

Even Brake active-assist exclusion · DUO Maverick regulator instructions

Blue Ox Patriot · BRK2022Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Patriot BRK2022 is a portable brake for a compatible footwell and pedal, with a constant 12V supply. Blue Ox expressly covers hybrids and continuous-assist brakes through its Hybrid mode; it does not require a motorhome air-brake connection.

What it does and who it suits

A powered actuator presses the truck’s brake pedal. The in-coach controller lets the driver monitor the brake and use the controls described in the manual. The unit is removed before driving the Maverick.

Pros — reasons to choose it

  • Useful when moving the main brake unit between separately equipped vehicles.
  • The manufacturer provides a specific Hybrid setting rather than asking the installer to treat the Maverick like a conventional vacuum-assisted car.

Cons — tradeoffs and limits

  • Positioning, pedal-clamp attachment and setup are repeated when the unit is reinstalled.
  • Needs reliable constant power, breakaway wiring and storage space; portable does not mean installation-free.

Example in practice

After a Ford-required start during a travel stop, follow Patriot’s restart/setup instructions before towing again. A ready light from earlier in the morning is not a substitute for the required reset.

Complete the application

Use Hybrid mode as directed, verify the monitor, and demonstrate pedal application and full release. Include a suitable powered outlet and charging plan in the quote.

Product instructions ↗

Blue Ox Patriot BRK2022 · product referenceEnlarge photo
Blue Ox Patriot BRK2022 · product reference. Photo: etrailer reference; not a Stellar customer installation.
Portable · electric

Blue Ox Patriot

BRK2022

Portable pedal actuator with an in-coach controller and included breakaway. Blue Ox lists compatibility with hybrids. The unit is removed from the footwell when driving.

What changes the installation?

Useful when transferring the main unit between approved vehicles. On the Maverick Hybrid, use the Patriot Hybrid mode, constant 12V power and the prescribed pedal setup. The breakaway installation stays with each vehicle.

Use the Patriot Hybrid mode as directed for hybrid vehicles, and reset the brake after starting the vehicle. Follow the linked manual’s setup checks.

Open Patriot BRK2022 manual PDF ↗Blue Ox official manual, Rev. D, October 2025. Confirm the revision for your unit.

Manufacturer details
CURT RVibrake 4 · 52202Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

CURT RVibrake 4 52202 is a portable floor-mounted actuator. Its manual supports both Vacuum and Active assist modes; the Maverick’s active-assist application needs the Active configuration and its prescribed brake test.

What it does and who it suits

Auto Position establishes the actuator position against the pedal and floor arrangement. The Bullseye monitor controls brake type, pressure and sensitivity; these are separate settings with different jobs.

Pros — reasons to choose it

  • Compact portable unit for an owner who wants transferability.
  • The manual explicitly explains Active assist operation and guided setup.

Cons — tradeoffs and limits

  • Must be positioned and set up each time; a required stop plate or other floor-fit accessory is part of the installation.
  • The default Vacuum setting is not an appropriate assumption for a Maverick Hybrid. Changing pedal position or restarting the truck can require setup again.

Example in practice

An owner stops to follow Ford’s engine-running routine. Before continuing, the owner repeats the brake manufacturer’s required positioning/reset steps and checks the monitor instead of assuming Auto Position remains valid.

Complete the application

The Active-mode instructions begin at 5 PSI and require the manual’s brake test to establish operation. This is a starting procedure, not a universal final pressure for every truck or coach.

Product instructions ↗

CURT RVibrake 4 52202 · product referenceEnlarge photo
CURT RVibrake 4 52202 · product reference. Photo: CURT reference; not a Stellar customer installation.
Portable · proportional

CURT RVibrake 4

52202

Compact floor-mounted system with Bullseye monitoring and a range extender. Check the application guide for any stop plate or other fit-specific component.

What changes the installation?

Follow its Auto Position process after installation and whenever the manual requires it, including after restarting the towed vehicle. Moving the pedal after setup can alter the actuator position. Pair the Ford stop routine with the brake manufacturer’s reset instructions.

Open manufacturer manual
Demco Stay-IN-Play DUO · 9599006 / 9599018Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Stay-IN-Play DUO is for a motorhome with hydraulic brakes. 9599006 is the listed standard package; 9599018 adds Wireless Coachlink. Demco’s current TB20051 manual specifically identifies additional regulator 6492 for a Ford Maverick installation.

What it does and who it suits

The installed system uses the coach’s brake-light input together with deceleration to command the Maverick’s pedal actuator. It stays installed, reducing the equipment placed in the footwell for each departure.

Pros — reasons to choose it

  • Convenient for frequent travel with the same truck.
  • Two operating inputs distinguish an actual slowing event from a brake-light signal alone.

Cons — tradeoffs and limits

  • More initial installation work and less convenient transfer to another vehicle than a portable unit.
  • The Maverick regulator, adjustment, pedal-cable geometry and full release are essential parts of the job. A generic DUO parts quote may omit the extra regulator.

Example in practice

A hydraulic-brake motorhome owner using the Maverick every weekend can compare DUO’s higher initial installation effort with repeated portable-unit setup. The quote should identify 6492 and the chosen monitor package.

Complete the application

Have the installer demonstrate normal operation, complete release, the breakaway test and the monitor. Demco requires adequate breakaway braking as well as avoiding wheel drag; simply turning pressure down is not a complete setup.

Product instructions ↗

Demco Stay-IN-Play DUO operating unit
Operating unit · Demco manufacturer product reference.
Installed · hydraulic-brake coach

Demco Stay-IN-Play DUO

9599006 / 9599018

Installed system for a motorhome with hydraulic brakes. Uses deceleration and the coach’s brake-light signal together. 9599018 is the Wireless Coachlink package.

What changes the installation?

Less equipment to position in the driver footwell for each trip. The installation must account for the Maverick’s brake-assist behavior, control-unit location, pedal cable geometry, breakaway and monitoring. Identify the coach’s actual brake system before choosing it.

Open manufacturer manual
Demco Air Force One · 9599007 / 9599019Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Air Force One is for a motorhome with air brakes. 9599007 and 9599019 are the listed package options, with Wireless Coachlink on 9599019. It is not the hydraulic-coach counterpart to DUO.

What it does and who it suits

A coach-side pneumatic connection communicates braking to the towed-vehicle system. Some motorhomes have a factory towed-brake connection, but the actual chassis package determines which installation components are needed.

Pros — reasons to choose it

  • Installed arrangement reduces daily portable-box setup.
  • Designed around an air-brake coach, with braking control tied to that coach’s air system.

Cons — tradeoffs and limits

  • May require coach-side installation as well as work on the Maverick.
  • A connector that looks like an air fitting does not establish an approved factory interface; identify its purpose and compatibility.

Example in practice

A diesel motorhome owner with an existing factory air-brake tow connection can potentially avoid duplicating some coach-side work. The installer first identifies the chassis connection, then specifies the matching Demco package and truck-side components.

Complete the application

The final scope needs the air line, breakaway, monitor, Maverick pedal/assist setup and complete release test. Motorhome size or fuel type alone does not identify its brake system.

Product instructions ↗

Installed · air-brake coach

Demco Air Force One

9599007 / 9599019

Air-brake-motorhome system; 9599019 adds Wireless Coachlink. Verify whether the coach already has a compatible factory towed-vehicle air connection.

What changes the installation?

The motorhome-side air integration is part of the job unless an approved existing connection is confirmed. A coach with hydraulic brakes needs a different system. Identify chassis, year and any factory tow-brake package rather than choosing by motorhome size alone.

Open manufacturer manual
Roadmaster InvisiBrake · 8700Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Roadmaster FitMaster identifies InvisiBrake as an applicable Roadmaster choice for the 2022–2026 Maverick Hybrid’s active brakes. The active-assist pressure setup is required; the factory setting cannot simply be assumed correct.

What it does and who it suits

The installed controller and pedal-actuating hardware remain in the truck. It receives the signals required by its wiring design and applies braking according to its adjustment; do not describe every installed brake as operating identically.

Pros — reasons to choose it

  • Avoids placing and removing a portable brake box at every stop.
  • Roadmaster publishes specific guidance for active-assist brakes and the associated Maverick signal requirements.

Cons — tradeoffs and limits

  • Requires permanent mounting space and careful cable routing.
  • Active-assist adjustment and a trustworthy pedal/brake signal are critical; an overly high setting can over-brake the truck.

Example in practice

For a 2025 Hybrid, Roadmaster lists the OEM brake switch as unusable for the required signal and identifies custom switch 751513 or universal 751000. That is a separate function from making the rear towing lamps illuminate.

Complete the application

Roadmaster identifies 20 PSI as the initial active-brake setting, followed by its adjustment procedure. For earlier Maverick years, its fitment notes instead call out brake-light relay 88400. Use the year-specific signal plan.

Product instructions ↗ · Manufacturer application / specifications ↗

Roadmaster InvisiBrake 8700 · product referenceEnlarge photo
Roadmaster InvisiBrake 8700 · product reference. Photo: etrailer reference; not a Stellar customer installation.
Installed · electric / pneumatic

Roadmaster InvisiBrake

8700

A permanently mounted option with a pedal actuator. Compare installation space, coach signal inputs and the exact vehicle-specific setup.

What changes the installation?

The brake manufacturer’s application and adjustment instructions govern. On a Hybrid, brake-assist behavior and pedal force need deliberate verification; applying a generic conventional-vehicle adjustment can produce too much or too little braking.

Open manufacturer manual
Roadmaster Even Brake · 9400Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Not a Maverick Hybrid recommendation. Roadmaster’s Even Brake 9400 manual explicitly prohibits use with active/continuous-assist brakes, and Roadmaster identifies the Maverick Hybrid as having that brake behavior.

What it does and who it suits

This portable proportional system is retained here to help owners identify existing equipment and understand why a brake that worked on a previous car may not transfer to the Maverick.

Pros — reasons to choose it

  • For a vehicle that actually meets its application, a portable design can be removed and stored.
  • Its model identification and manual make the active-brake exclusion clear.

Cons — tradeoffs and limits

  • The active-brake prohibition excludes the Maverick Hybrid application described by Roadmaster.
  • A lower generic sensitivity setting, a good pedal fit or an adequate 12V outlet does not override that prohibition.

Example in practice

An owner moving an Even Brake from an older conventional-brake vehicle to a Maverick should select a suitable active-assist system instead of reinstalling the existing unit and hoping a lighter setting is enough.

Complete the application

Compare Patriot in Hybrid mode, RVibrake 4 in its Active configuration, or an approved installed application. Within Roadmaster’s range, its Maverick notes identify InvisiBrake or BrakeMaster with the required reducer.

Product instructions ↗

Roadmaster Even Brake 9400 · product referenceEnlarge photo
Roadmaster Even Brake 9400 · product reference. Photo: Roadmaster reference; not a Stellar customer installation.
Portable · proportional

Roadmaster Even Brake

9400

Not recommended for Maverick Hybrid: the Even Brake 9400 manual prohibits active/continuous-assist brake applications. Retained here to identify existing equipment and explain the incompatibility.

What changes the installation?

A suitable clamp, working power supply or reduced sensitivity cannot override the active-brake exclusion. Choose a system with the required Maverick active-assist application.

Open manufacturer manual
Roadmaster BrakeMaster · 9060 / 9160Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

BrakeMaster 9060 is the hydraulic-coach version; 9160 is the air-brake-coach version. Roadmaster’s Maverick Hybrid application requires Brake Pressure Reducer 900002 and lists seat adapter 88357; the mounting post is not included in that seat-adapter kit.

What it does and who it suits

A removable pedal cylinder works with installed vehicle and coach components. This sits between a portable box and a fully out-of-the-way installed actuator in terms of daily handling.

Pros — reasons to choose it

  • Versions are designed for the two different motorhome brake types.
  • The cylinder can be removed for driving while the supporting installation remains in place.

Cons — tradeoffs and limits

  • The active-brake reducer is required for this application, not an optional convenience accessory.
  • Cylinder attachment and removal remain part of the travel routine, and the hydraulic/air versions have different coach-side requirements.

Example in practice

An air-brake coach owner considering 9160 for a 2024 Hybrid needs more than the cylinder: the estimate should identify 900002, 88357, the mounting post, signal/monitor arrangement and breakaway equipment.

Complete the application

Verify cylinder geometry, release and the model-specific coach connections. Never substitute the instructions for 9060 when installing the air-coach components of 9160.

Product instructions ↗ · Manufacturer application / specifications ↗

Roadmaster BrakeMaster pedal cylinder · manufacturer reference vehicleEnlarge photo
Roadmaster BrakeMaster pedal cylinder · manufacturer reference vehicle. Photo: Roadmaster reference; not a Stellar customer installation.
Coach-specific · pedal cylinder

Roadmaster BrakeMaster

9060 / 9160

9060 is the hydraulic-coach system; 9160 is the air-brake-coach system with breakaway. Treat these as application-dependent alternatives.

What changes the installation?

Do not select solely by price. Confirm the Maverick’s current application approval, any required pressure regulation and the cylinder mounting method. The exact components differ with the coach’s braking system.

Open manufacturer manual
NSA Ready Brake / Elite II · RB-9050-2 systemClick for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

Ready Brute Elite II combines an 8,000-lb bar with mechanical surge braking. NSA sells different clevis options, including Blue Ox, Demco Classic and Roadmaster hole-size versions; choose the one approved for the actual baseplate.

What it does and who it suits

As the towed vehicle pushes against the slowing coach, the surge mechanism pulls an installed cable that applies the truck’s brake pedal. It is a different operating approach from a portable electric pedal actuator.

Pros — reasons to choose it

  • Combines the tow-bar and normal supplemental-braking mechanism in one system.
  • Removes the need to position a portable brake box in the driver footwell at every campsite.

Cons — tradeoffs and limits

  • Cable routing, free movement and adjustment are essential installation work; the bar by itself does not complete the brake installation.
  • Breakaway, monitoring and the exact Maverick active-assist application must be addressed explicitly. Mechanical operation is not a reason to ignore the Hybrid’s pedal response.

Example in practice

An owner comparing Elite II with a separate tow bar and DUO should compare complete installed systems: include the NSA vehicle cable, breakaway and monitor before comparing totals.

Complete the application

Do not confuse Ready Brute II with Ready Brute Elite II: NSA states the non-Elite tow bar lacks the integrated surge brake. Have the installer demonstrate full pedal release.

Product instructions ↗ · Manufacturer application / specifications ↗

NSA Ready Brute Elite II · RB-9050-2Enlarge photo
NSA Ready Brute Elite II · RB-9050-2
Image: NSA · manufacturer reference
Mechanical · surge braking

NSA Ready Brake / Elite II

RB-9050-2 system

The Elite II tow-bar option incorporates mechanical surge braking, using a properly installed cable to operate the truck’s pedal.

What changes the installation?

The tow bar alone is not the finished installation. Cable routing and adjustment, a compatible connection, monitoring and an appropriate breakaway arrangement need to be specified. Confirm manufacturer approval for the exact Hybrid and its brake-assist operation.

Manufacturer details
CURT RVibrake Shadow 2 · 52201Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Pros, cons & Maverick application

What it works with

RVibrake Shadow 2 52201 is an installed brake with Bullseye monitoring and integrated battery charging. Its manual excludes hydroboost vehicles; an exact Maverick installation still needs the correct pedal-actuator and brake-assist configuration.

What it does and who it suits

It reduces daily equipment handling by leaving the operating components installed. Its charging feature is a separate electrical function whose output depends on a working coach supply and wiring path.

Pros — reasons to choose it

  • No portable box to set in the footwell at each campsite.
  • Integrated charging can reduce duplicate equipment when the entire power plan is designed around it.

Cons — tradeoffs and limits

  • Installation is more involved than moving a portable unit between vehicles.
  • The advertised up-to-10-amp charging function cannot deliver power from a dead or unpowered motorhome socket.

Example in practice

A frequent traveler comparing Shadow 2 with RVibrake 4 can decide whether reduced daily handling is worth the permanent installation. Compare full installation prices, including the coach-to-truck power path.

Complete the application

Verify the current Maverick application, test monitor operation and full pedal release, and measure charging under load. Automatic detection does not replace Ford’s Neutral Tow procedure.

Product instructions ↗

CURT RVibrake Shadow 2 52201 · product referenceEnlarge photo
CURT RVibrake Shadow 2 52201 · product reference. Photo: CURT reference; not a Stellar customer installation.
Installed · proportional

CURT RVibrake Shadow 2

52201

An installed alternative with tow-mode detection, Bullseye monitoring and a built-in battery charger rated up to 10 amps by CURT.

What changes the installation?

Confirm the current application guide, any required accessories and the actual 12V supply. Automatic brake operation does not remove Ford’s Neutral Tow steps, scheduled stops or the need to verify the brake monitor before departure.

Manufacturer details
Brake Buddy Select 3 · 39524Click for application, pros & cons, examples, photos and manualsTap to close+ Add to my inquiry

Manuals & installation instructions

Hopkins / Brake Buddy 39524 instructions, hosted by ManualsLib. The manufacturer’s own PDF website was unavailable when checked; confirm the revision for your unit.

Pros, cons & Maverick application

What it works with

Brake Buddy Select 3 39524 is a portable pedal brake with selectable braking behavior. This guide has not established a current manufacturer-approved Maverick Hybrid setting for this exact model; it is an existing-equipment comparison, not a confirmed Maverick recommendation.

What it does and who it suits

It is useful to identify when an owner already has one and is deciding what can transfer. The operating mode and pedal force must suit active assist, not simply the approximate vehicle weight.

Pros — reasons to choose it

  • Portable format allows the main unit to be removed for driving and potentially used in another expressly approved vehicle.
  • Selectable behavior gives an approved application choices described in its own manual.

Cons — tradeoffs and limits

  • A universal marketing description or pedal clamp that fits is insufficient evidence of Maverick Hybrid compatibility.
  • Current power, breakaway, monitor and assist-setting requirements must be resolved for 39524 before purchase or reuse.

Example in practice

If an owner already has a Select 3, record its complete model and revision and obtain Brake Buddy’s application answer. If that answer is unavailable, compare an alternative with published active-assist instructions.

Complete the application

The linked document is a hosted manufacturer-manual copy because the manufacturer PDF host was unavailable during review. Do not apply instructions from a different Brake Buddy model.

Product instructions ↗

Brake Buddy Select 3 39524 · product referenceEnlarge photo
Brake Buddy Select 3 39524 · product reference. Photo: Hopkins / PPL Motor Homes reference; not a Stellar customer installation.
Portable · selectable braking

Brake Buddy Select 3

39524

A portable Brake Buddy option with selectable braking behavior. Include it when comparing an existing Select 3 or a proposed package, with current application and availability verification.

What changes the installation?

Use the manufacturer’s instructions for vehicle-specific setup, pedal clamp, power, breakaway and remote operation. On a Maverick Hybrid, confirm the appropriate brake-assist settings and a suitable power arrangement before selecting the system.

Open manufacturer manual

Previous 15Next 15 brakes
Maverick Hybrid brake-assist behavior matters.Read this important informationTap to close
Maverick Hybrid brake-assist behavior matters.Verify the braking manufacturer’s current vehicle instructions and setup in Ford’s actual Neutral Tow state. Include breakaway protection, driver monitoring and a functional test. Do not assume a conventional vacuum-brake setup or a generic gain setting is correct.
Stay-IN-Play DUO: a Maverick-specific regulator check.Read this important informationTap to close
Stay-IN-Play DUO: a Maverick-specific regulator check.Demco’s September 2026 manual (TB20051 Rev. 19) identifies an additional 6492 air-pressure regulator for Maverick installation. Older revisions use a different reference. Confirm the current kit with Demco, then follow its adjustment and testing instructions for normal braking, complete release and breakaway operation. Read the current Demco manual.
See the brake unit and pedal actuatorTap to readTap to close
Demco Stay-IN-Play DUO operating unit
Operating unit · Demco manufacturer product reference.
Demco brake pedal actuator shown in a reference installation
Pedal actuator · Demco reference installation, not a Maverick fitment illustration. Follow the exact vehicle instructions.
Which brake type suits your motorhome?Tap to readTap to close
Your priority / coachOptions to compareInstallation tradeoff
Transfer equipment between vehiclesPatriot in Hybrid mode; RVibrake 4 in Active modeMore setup and removal each trip; permanent breakaway wiring still required.
Hydraulic-brake motorhome; less daily setupStay-IN-Play DUO; applicable installed alternativesMore initial vehicle installation; verify vehicle-specific brake-assist setup.
Air-brake motorhomeAir Force One; applicable BrakeMaster systemCoach-side air equipment and chassis compatibility must be confirmed.
Mechanical surge systemReady Brute Elite II / Ready Brake familyCable routing and adjustment are critical; specify monitoring and breakaway separately.

Tell us whether your motorhome has hydraulic or air brakes. If you are unsure, send its year, make, model and chassis.

Plan my installation
Choose another section ↑
About this topicRead the full introductionTap to close

Supplemental braking operates the Maverick’s service brakes. The breakaway system applies them if the vehicles separate. Neither function is provided by the tow bar, safety cables or tail-light wiring alone.

Choose another topicNext section →

Equipment / Lighting

Make every signal reach the truck.

Tap an option to open it. Tap it again to close it.

Maverick wiring applications · reviewed November 10, 2026

Which wiring works with which Maverick?

Start with the rear lamps and the exact model year. LED headlamps, bed lighting and a trailer-tow package do not identify the taillight circuit used for flat towing. The table below separates published Maverick applications from components selected by circuit type.

2022–2024 Maverick HEV

Published wiring choices: Blue Ox lists BX8848 for this HEV application. Roadmaster’s entries for all three years permit universal diode wiring and identify combined stop/turn lighting.

Additional signal part: Roadmaster calls out brake-light relay 88400 when using supplemental braking. The relay addresses the truck’s own brake-light signal interfering with the RV’s turn signal; it is separate from the diodes.

Blue Ox 2022–2024 application · Roadmaster 2024 requirements

2025–2026 Maverick HEV

Published wiring choices: Blue Ox lists BX8848 on its 2025–2026 HEV application. Roadmaster’s 2025 and 2026 entries allow universal diode wiring.

Additional signal part: Roadmaster lists the OEM brake switch as unusable for the required supplemental-brake signal and identifies custom switch 751513 or universal 751000. Do not carry the earlier-year relay answer forward as though a relay and a brake switch perform the same job.

Blue Ox 2025–2026 application · Roadmaster 2026 requirements

Factory rear-lamp differences

Ford’s 2025 specifications list halogen taillamps on XL and XLT, and LED taillamps on Lariat. The 2025 Black Appearance Package adds LED taillamps to XLT. Ford’s 2026 order guide likewise lists LED taillamps for Lariat and the XLT Black Appearance Package. Check the actual build and any lamp replacements; trim alone can miss that exception.

Ford 2025 lamp specifications · 2025 package details · 2026 package details

LED does not automatically mean Smart Diodes

Lamp technology describes the bulb or assembly. Variable-voltage control describes how the circuit commands different light functions. Roadmaster permits its LED Smart Diodes on suitable normal or variable-voltage LED circuits; its conventional 15267 is excluded from variable-voltage applications. Incandescent Smart kit 153267 and LED Smart kit 153967 are different products.

Roadmaster’s exact kit distinctions

Example: a 2025 XLT and a 2025 XLT with the Black Appearance Package

The badges both say XLT, but Ford’s package changes the rear lamps to LED. That is why the parts worksheet records the rear-lamp assembly and package, not just “2025 Maverick.” Both owners can consult the published HEV wiring applications above; a Smart Diode choice, if used, must match the actual lamp type and circuit.

Diode, relay, brake switch and charge line: four different jobs

  • Diode: isolates or conditions the towing-light input at the lamp circuit.
  • Brake-light relay: prevents an unwanted factory brake-light input from overriding the towing turn signal where the installation calls for one.
  • Supplemental-brake switch: supplies the required brake/pedal signal when the factory switch cannot provide a usable one.
  • Charge line: supplies protected 12V support. It does not create a brake command or fix a lighting conflict.

Roadmaster’s checked Maverick applications say no bulb-and-socket kit. A separately drilled bulb arrangement should not be offered as a default alternative to the listed diode approach. Its recommendation to use InvisiBrake or BrakeMaster is within Roadmaster’s own brake range; other brands must follow their own published active-assist applications.

See a diode wiring kitTap to readTap to close
Lighting example

The diodes isolate the lighting circuits.

This manufacturer product photo shows the kit components. A complete plan still needs the correct socket, cord, wiring method and functional test for the truck’s actual lamps.

Browse electrical documents ↑
Compare lighting approaches and part numbersTap to readTap to close
Wiring approachReference partsWhat it does / what to verify
Roadmaster diode wiring
Roadmaster diode wiring kit 15267 · product referenceEnlarge photo
Roadmaster diode wiring kit 15267 · product reference. Photo: etrailer reference; not a Stellar customer installation.
Roadmaster 4-way diode wiring kit 154 · product referenceEnlarge photo
Roadmaster 4-way diode wiring kit 154 · product reference. Photo: etrailer reference; not a Stellar customer installation.
15267 · 154Roadmaster FitMaster lists universal diode wiring for the 2022, 2023, 2024, 2025 and 2026 Maverick Hybrid applications checked. The 15267 uses that conventional four-diode approach and includes a 7-to-6 coiled cord and front socket. Roadmaster excludes variable-voltage circuits from 15267.
Click for application, pros, cons & examplesUnderstand the circuit, kit contents and installationClose the detailed explanation
+ Add to my inquiry

Pros, cons & Maverick application

What it works with

Roadmaster FitMaster lists universal diode wiring for the 2022, 2023, 2024, 2025 and 2026 Maverick Hybrid applications checked. The 15267 uses that conventional four-diode approach and includes a 7-to-6 coiled cord and front socket. Roadmaster excludes variable-voltage circuits from 15267.

What it does and who it suits

The diodes allow the motorhome to operate the truck’s existing rear lamps while isolating the two vehicles’ lighting supplies. This is a splice-in installation, not a Maverick-specific plug-in harness.

Pros — reasons to choose it

  • Uses the installed truck lamps, so there is no separate light bar to mount each trip.
  • The included 7-to-6 connection provides a useful starting point for a separately installed charge circuit.

Cons — tradeoffs and limits

  • Factory lighting wires are spliced, and the correct circuit must be identified at the lamps.
  • A charge wire, brake signal interface and active-assist brake are separate components; the lighting kit does not supply them all.

Example in practice

For a stock 2025 Hybrid, start with Roadmaster’s Maverick universal-wiring application. Do not decide that an LED headlamp automatically requires LED Smart Diodes at the rear. If the actual taillight circuit is variable-voltage, choose the appropriate Smart Diode arrangement instead.

Complete the application

15267 is the 7-to-6 package. Roadmaster 154 supplies a 4-flat lighting connection; it does not provide the separate auxiliary charging circuit through that 4-flat cord.

Product instructions ↗ · Manufacturer application / specifications ↗

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Blue Ox diode wiring
Blue Ox diode wiring kit BX8848 · product referenceEnlarge photo
Blue Ox diode wiring kit BX8848 · product reference. Photo: Blue Ox reference; not a Stellar customer installation.
BX8848Blue Ox explicitly lists BX8848 as a wiring option for Maverick HEV 2022–2024 on the BX2913 application and 2025–2026 on the BX2917 application. Those are vehicle-specific manufacturer listings, not an assumption based on a universal label.
Click for application, pros, cons & examplesUnderstand the circuit, kit contents and installationClose the detailed explanation
+ Add to my inquiry

Pros, cons & Maverick application

What it works with

Blue Ox explicitly lists BX8848 as a wiring option for Maverick HEV 2022–2024 on the BX2913 application and 2025–2026 on the BX2917 application. Those are vehicle-specific manufacturer listings, not an assumption based on a universal label.

What it does and who it suits

BX8848 uses four diodes to connect the RV’s left stop/turn, right stop/turn and running-light signals to the truck’s lamps. The diodes limit electrical feedback into the original lighting circuits.

Pros — reasons to choose it

  • Published Blue Ox Maverick HEV application across both body generations.
  • Uses the truck’s own rear lamps and can be used independently of the tow-bar brand when the complete wiring design is appropriate.

Cons — tradeoffs and limits

  • Requires wire identification and splicing behind the lamps. It is not a plug-and-play Maverick connector kit.
  • The instruction-sheet parts list does not include the coach-to-truck umbilical and front socket; specify those separately.

Example in practice

An owner with a 2024 Hybrid and a Roadmaster tow bar can still compare the BX8848 wiring approach. Mechanical tow-bar brand and electrical lamp wiring are separate choices.

Complete the application

The published application covers the stock HEV lighting arrangement. An aftermarket lamp conversion needs its own circuit review. Use the manufacturer’s diagram rather than assuming Ford wire colors match the kit’s green, yellow, brown and white harness wires.

Product instructions ↗ · Manufacturer application / specifications ↗ · 2022–2024 HEV listing ↗

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Demco diode wiring
Demco diode wiring kit · 9523010Enlarge photo
Demco diode wiring kit · 9523010
Image: Demco · manufacturer reference
9523010Demco 9523010 is a universal hardwired taillight/diode kit for conventional vehicle lighting circuits. The documents checked do not provide a separate Maverick year/trim approval for this kit; it is a circuit-based alternative rather than a confirmed plug-in Maverick fit.
Click for application, pros, cons & examplesUnderstand the circuit, kit contents and installationClose the detailed explanation
+ Add to my inquiry

Pros, cons & Maverick application

What it works with

Demco 9523010 is a universal hardwired taillight/diode kit for conventional vehicle lighting circuits. The documents checked do not provide a separate Maverick year/trim approval for this kit; it is a circuit-based alternative rather than a confirmed plug-in Maverick fit.

What it does and who it suits

The kit connects the motorhome’s running, turn and brake-light functions to the towed vehicle through isolating diodes. It is different from Demco’s vehicle-specific Towed Connector harnesses.

Pros — reasons to choose it

  • Permanent wiring uses the vehicle’s rear lamps.
  • Can be considered as part of a Demco accessory package without requiring the tow bar and wiring to share a brand.

Cons — tradeoffs and limits

  • Splicing is required, and the conventional diode diagram is not proof of compatibility with every variable-voltage or modified LED circuit.
  • The diode kit alone is not the complete motorhome-to-truck connection; cord, socket and charge wiring must be specified.

Example in practice

If a quote says only “Demco wiring,” ask which part: 9523010 is the hardwired diode kit, while a Towed Connector requires an exact vehicle-specific harness number.

Complete the application

For a buyer wanting an explicit published Maverick application, the Blue Ox BX8848 listings and Roadmaster FitMaster universal-wiring entries provide that evidence. Do not label 9523010 a no-splice Maverick harness.

Product instructions ↗ · Manufacturer application / specifications ↗

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Roadmaster smart diodes
Roadmaster LED Smart Diode 787 · product referenceEnlarge photo
Roadmaster LED Smart Diode 787 · product reference. Photo: Roadmaster reference; not a Stellar customer installation.
787 / 789 familyRoadmaster 787 is one LED Smart Diode; 789 is the two-pack. These are for LED lamp circuits, including variable-voltage/multiplex operation. The complete 7-to-6 LED Smart kit is 153967. Incandescent lamps use a different Smart Diode family; the corresponding complete kit is 153267.
Click for application, pros, cons & examplesUnderstand the circuit, kit contents and installationClose the detailed explanation
+ Add to my inquiry

Pros, cons & Maverick application

What it works with

Roadmaster 787 is one LED Smart Diode; 789 is the two-pack. These are for LED lamp circuits, including variable-voltage/multiplex operation. The complete 7-to-6 LED Smart kit is 153967. Incandescent lamps use a different Smart Diode family; the corresponding complete kit is 153267.

What it does and who it suits

A conventional diode mainly isolates current. A Smart Diode also conditions the RV signal for the lamp’s operating voltage, allowing the correct brightness/function on a compatible circuit.

Pros — reasons to choose it

  • Addresses the variable-voltage behavior that a conventional diode cannot reproduce.
  • Roadmaster permits suitable Smart Diodes on normal circuits too; they are not limited to vehicles where they are mandatory.

Cons — tradeoffs and limits

  • An LED version is not the interchangeable choice for an incandescent lamp circuit.
  • LED lamps and multiplex/variable-voltage control are different facts. A truck having LED lights does not by itself establish that ordinary diodes are unsuitable.

Example in practice

A 2025 Lariat has LED taillamps, while a standard XL or XLT has halogen taillamps. The installer identifies the actual rear circuit before choosing LED Smart, incandescent Smart or the manufacturer-listed conventional wiring arrangement.

Complete the application

The Maverick FitMaster entries checked allow universal diode wiring. This guide therefore does not claim every Maverick requires Smart Diodes. Choose a complete kit when you also need the harness, socket and cord.

Product instructions ↗ · Manufacturer application / specifications ↗

Manuals & installation instructions

This schematic is for 789 LED Smart Diodes. Confirm the exact diode and complete kit number before wiring; it is not a universal diagram for every 787 / 789 kit.

Separate wireless light bar
Demco wireless LED light bar 6343 · product referenceEnlarge photo
Demco wireless LED light bar 6343 · product reference. Photo: Demco reference; not a Stellar customer installation.
Demco 6343Demco 6343 is a separate wireless rear light bar, not a splice-in interface to a particular Ford lamp. Its application depends on a suitable mounting position, rearward visibility and the specified transmitter/power arrangement rather than whether the Maverick has halogen or LED factory lamps.
Click for application, pros, cons & examplesUnderstand the circuit, kit contents and installationClose the detailed explanation
+ Add to my inquiry

Pros, cons & Maverick application

What it works with

Demco 6343 is a separate wireless rear light bar, not a splice-in interface to a particular Ford lamp. Its application depends on a suitable mounting position, rearward visibility and the specified transmitter/power arrangement rather than whether the Maverick has halogen or LED factory lamps.

What it does and who it suits

The light bar receives the motorhome’s lighting commands and supplies the separate rear signals. This avoids cutting into the Maverick taillight circuits, but moves the installation questions to mounting, signal reception and power.

Pros — reasons to choose it

  • Avoids splices into factory rear-lamp wiring.
  • Useful to compare when a separate rear signal device is preferable to modifying the truck’s lamps.

Cons — tradeoffs and limits

  • A rear-window installation must remain visible through the actual glass, tint and cargo arrangement.
  • Wireless operation still needs the prescribed power and a full signal check; it does not provide braking or battery charging.

Example in practice

A truck with a bed cap or heavily tinted rear glass needs a visibility review before selecting a rear-window light-bar location. A successful bench test does not prove it can be seen by traffic behind the assembled rig.

Complete the application

Confirm mounting and signal operation on the actual truck. The linked manufacturer setup page is available; a separate current 6343 PDF was not located.

Product instructions ↗ · Manufacturer application / specifications ↗

Manuals & installation instructions

A separate current PDF was not available on the manufacturer page when checked. Use the included 6343 instructions or request them from Demco before setup.

Vehicle-specific plug-in harnessExact application requiredNo exact Maverick towed-vehicle plug-in harness part number was established from the manufacturer listings checked. CURT 56477 and 56567 are trailer-output harnesses, not substitutes for an RV-to-Maverick lighting harness.
How the lighting connection worksTap to readTap to close
1 · Coach lighting outputVerify running lights, left and right stop/turn signals and ground at the RV connector.
2 · Cord & front socketConfirm each terminal by function and provide enough length for turns without dragging.
3 · Truck-side lightingIsolate the correct circuits or use a separately powered, securely mounted light system.
A 6-way center pin is not proof of a charge circuit.Read this important informationTap to close
A 6-way center pin is not proof of a charge circuit.Terminal assignments can differ between installed connectors and adapters. Identify both ends electrically before connecting them. Wire color alone is not a reliable pinout. A mistaken charge/brake assignment can damage equipment.
Lighting tests and trailer-wiring differencesTap to readTap to close

How the final lighting check works

With the Maverick in its actual towing configuration, test running lights, left turn, right turn, brake lights and combined brake/turn operation. Then verify the supplemental brake does not create a misleading signal or backfeed.

Why a trailer wiring kit is different

The Maverick’s trailer socket sends signals out to a trailer. Flat-tow wiring receives signals from the motorhome and operates the truck’s lights. Those are opposite jobs, so the 4K Tow Package does not supply a complete flat-tow lighting solution.

Choose another section ↑
About this topicRead the full introductionTap to close

Lighting wiring, battery charging and brake control are separate circuits. Plan them together, label them clearly and test the complete connection in towing mode.

Plug-in harnesses: avoid the wrong kind of Maverick kit

A vehicle-specific towed-vehicle harness would plug into the truck’s lamps and receive signals from the RV. No exact Maverick towed-harness part number was established from the manufacturer listings checked for this update. Demco’s published Towed Connector chart does not list Maverick; its universal 9523010 diode kit is a different product.

Concrete examples of the wrong function: CURT 56477 and 56567 are Maverick-related trailer-output harnesses. They power a trailer behind the Maverick; they are not RV-to-Maverick flat-tow lighting harnesses. A product page saying “fits Maverick” is not enough if it performs the opposite job.

Pros of a properly listed towed harness: fewer factory-wire splices and matched connectors. Cons: it must have the exact year/lamp application; a physically matching plug does not establish signal compatibility. Use the documented diode choices above unless an exact current towed-harness application is supplied.

Demco towed-harness application chart · CURT 56477 function and applications · CURT 56567 function and applications

Choose another topicNext section →

Equipment / Charging

Protect the power that towing depends on.

Tap an option to open it. Tap it again to close it.

Follow the whole 12V path

Coach battery/supply → protected coach charge circuit → RV socket → cord → Maverick front socket → protected truck-side charge line → Maverick 12V battery. Every link has to work. Roadmaster’s checked 2022–2026 Hybrid applications identify battery drain during towing and list truck-side 156-25 and coach-side 156-75. They also identify outlet 9332 when the chosen brake plugs into a 12V socket.

156-25 and CURT 52113 are alternative truck-side approaches. 156-75 is the coach-side solution when a suitable supply is missing. A four-flat lighting cord carries ground and three lighting functions; it does not also carry a dedicated charge feed.

Example: lights work, but the battery still runs down

Working lights demonstrate the lighting circuits, not the auxiliary charge path. Check the coach charge terminal in its travel state, the cord’s charge conductor, both grounds and the truck-side protection. Measure through the connected system with the brake powered. Seeing voltage at an unplugged socket does not prove useful current reaches the battery.

Integrated charging: RVibrake Shadow 2

Shadow 2 52201 advertises charging up to 10 amps. Pro: it can be part of one planned brake/power installation. Con: the feature still depends on the coach supply and wiring; do not add a second charging arrangement without designing how the circuits work together. Other brake models should not be assumed to include that feature.

Maverick electrical requirements · Shadow 2 installation instructions

2025–2026 Ford guidance calls for external 12V power with an add-on braking system.Read this important informationTap to close
2025–2026 Ford guidance calls for external 12V power with an add-on braking system.The current online Hybrid recreational-towing instructions warn that an add-on brake can discharge the battery and direct owners to connect an external 12V source while towing. Include a verified power solution in the plan. The exact vehicle manual and brake instructions govern.
Charge-line parts and what they doTap to readTap to close
ComponentReference partRole
Truck-side charge line
Roadmaster truck-side charge line 156-25 · product referenceEnlarge photo
Roadmaster truck-side charge line 156-25 · product reference. Photo: etrailer reference; not a Stellar customer installation.
Roadmaster 156-25Roadmaster 156-25 is the towed-vehicle side of a 12V maintenance-charge circuit, and Roadmaster lists it in the 2022–2026 Maverick Hybrid applications checked. It requires a working coach charge supply and a suitable six-wire or 7-to-6 cord/socket arrangement.
Click for application, pros, cons & examplesUnderstand the circuit, kit contents and installationClose the detailed explanation
+ Add to my inquiry

Pros, cons & Maverick application

What it works with

Roadmaster 156-25 is the towed-vehicle side of a 12V maintenance-charge circuit, and Roadmaster lists it in the 2022–2026 Maverick Hybrid applications checked. It requires a working coach charge supply and a suitable six-wire or 7-to-6 cord/socket arrangement.

What it does and who it suits

It carries protected power from the truck’s front towing socket to the specified low-voltage battery connection. It supports the Maverick’s 12V system; it is not a charger for the high-voltage hybrid traction battery.

Pros — reasons to choose it

  • A simple protected truck-side charge path.
  • Published instructions explain the required matching coach-side circuit and cord.

Cons — tradeoffs and limits

  • Does nothing if the motorhome’s auxiliary charge terminal is unpowered or the cord lacks that conductor.
  • The up-to-15-amp description is a limit, not guaranteed delivered current; wiring resistance and available coach supply affect performance.

Example in practice

If the Maverick battery falls during towing, first measure the coach supply through the connected cord under load. Installing another 156-25 cannot repair a failed coach fuse or an unused charge pin.

Complete the application

Pair it with an already adequate coach circuit or the correctly installed 156-75 where needed. Verify the pin assignment at both ends instead of assuming every six-pin socket uses the same center-pin function.

Product instructions ↗

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Coach-side charge line
Roadmaster motorhome-side charge line 156-75 · product referenceEnlarge photo
Roadmaster motorhome-side charge line 156-75 · product reference. Photo: etrailer reference; not a Stellar customer installation.
Roadmaster 156-75Roadmaster 156-75 is installed on the motorhome when it lacks a suitable protected charge supply to the rear connector. It works with a truck-side circuit such as 156-25; it is not a replacement for that truck-side circuit.
Click for application, pros, cons & examplesUnderstand the circuit, kit contents and installationClose the detailed explanation
+ Add to my inquiry

Pros, cons & Maverick application

What it works with

Roadmaster 156-75 is installed on the motorhome when it lacks a suitable protected charge supply to the rear connector. It works with a truck-side circuit such as 156-25; it is not a replacement for that truck-side circuit.

What it does and who it suits

It completes the coach end of the path that can help maintain the Maverick’s 12V battery during towing. Roadmaster’s Maverick entries identify both sides because either end can be the missing piece.

Pros — reasons to choose it

  • Addresses an unpowered coach towing-connector charge terminal.
  • Can support a planned truck-side charge line without changing the selected taillight diode brand.

Cons — tradeoffs and limits

  • Unnecessary duplication if the coach already has a suitable factory circuit.
  • Requires routing and protection on the motorhome; a rear socket with seven contacts does not prove that its charge contact is connected.

Example in practice

A coach has working stop/turn lights at the rear plug but no auxiliary power. The lighting can pass its test while the Maverick receives no charge. The coach-side circuit must be corrected before evaluating the truck-side kit.

Complete the application

Test with the coach in its intended travel state and through the actual umbilical. Document which fuse or breaker protects each end so a later fault can be diagnosed.

Product instructions ↗

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Alternative charge-line kit
CURT dinghy charge line kit 52113 · product referenceEnlarge photo
CURT dinghy charge line kit 52113 · product reference. Photo: CURT / Lippert reference; not a Stellar customer installation.
CURT 52113CURT 52113 is an alternative truck-side dinghy charge-line kit. Its instructions require a 7-to-6 supply cord, a six-way car-end connector and, where missing, a coach charge circuit; those items are not all included in the kit.
Click for application, pros, cons & examplesUnderstand the circuit, kit contents and installationClose the detailed explanation
+ Add to my inquiry

Pros, cons & Maverick application

What it works with

CURT 52113 is an alternative truck-side dinghy charge-line kit. Its instructions require a 7-to-6 supply cord, a six-way car-end connector and, where missing, a coach charge circuit; those items are not all included in the kit.

What it does and who it suits

This adds a protected low-voltage charge path from the towing socket to the vehicle’s specified battery connection. It serves the same general truck-side role as 156-25, not the coach-side role of 156-75.

Pros — reasons to choose it

  • Provides a defined truck-side wiring and protection arrangement.
  • Can be compared independently of the chosen tow-bar and baseplate brand.

Cons — tradeoffs and limits

  • The manual specifies a 15-amp maximum protected battery connection; increasing protection size is not an upgrade.
  • An owner still needs the socket, bracket, suitable cord and functioning coach supply.

Example in practice

Compare a 52113 quote with a 156-25 quote only after both include the same missing socket, cable and coach-side work. A lower kit price alone may hide an incomplete power path.

Complete the application

Measure the completed system with the brake powered. Preserve the Maverick’s prescribed battery connection/monitoring arrangement and follow both the kit and vehicle instructions.

Product instructions ↗

Manuals & installation instructions

Opens in a new tab. Match the part number and revision to your equipment; save the PDF for your installation and travel records.

Integrated charging optionBrake-system-specificSome installed brake packages include a charging function. Verify the actual kit and usable output; do not add or omit hardware from a name alone.
How we check the 12V supplyTap to readTap to close

Start with a healthy 12V battery

Test the low-voltage battery and connections. A charge line is not a repair for a failing battery, loose terminal or abnormal vehicle draw.

Test the motorhome supply under load

Verify the charge terminal is powered in the required coach operating state, then check voltage and available current through the connected cord. Open-circuit voltage alone does not prove the circuit can support the load.

Protect and route the circuit correctly

Follow the kit’s specified wire size, circuit protection, ground and connection points. Protect wiring from heat, movement and sharp edges. Preserve the vehicle’s battery-monitoring arrangement as directed.

Verify the assembled system

Check charging at the Maverick with the brake system powered and all towing connections installed. Confirm that the system remains supported during the intended travel routine and that nothing is backfeeding unexpectedly.

This concerns the 12V electrical system.Read this important informationTap to close
This concerns the 12V electrical system.It is not a connection to the Hybrid’s high-voltage traction battery. Do not disconnect the 12V battery as a generic towing shortcut: the vehicle needs electrical power to enter and exit Neutral Tow. Follow Ford’s exact procedure.
Choose another section ↑
About this topicRead the full introductionTap to close

The brake unit and vehicle electronics create a real 12V demand. A wire connected to a socket is not enough; the coach, cord, circuit protection and truck-side connection all have to work.

Choose another topicNext section →

Plan your installation

What a complete setup includes.

Tap an option to open it. Tap it again to close it.

Everything a complete quote should includeTap to readTap to close
The complete installationWhat should be identified in the quote
VIN-specific baseplateManufacturer part number, required structural hardware, removable arms and permitted fascia/shutter changes.
Tow bar & connectionExact model, receiver size, approved adapters or crossbar, pins and retaining clips.
Safety cablesCorrect rating, approved attachment points, sufficient turning travel and routing clear of the ground.
Supplemental brake & breakawayCoach type, vehicle compatibility, pedal installation, switch, power supply and driver monitoring.
LightingTail-light solution, front socket, coach-to-truck cord, isolation and combined-signal test.
12V supportCoach output test, protected charge circuit or other approved power solution, and final test under operating load.
Height & clearanceActual receiver/baseplate measurements, approved rise/drop equipment if needed, turning clearance and accessory compatibility.
Verification & owner handoffFord mode demonstration, brake and light tests, connection practice, applicable manuals and written warranty terms.
Compare three ways to build the systemTap to readTap to close
Travel flexibility

Portable-first system

Compare an approved baseplate/bar combination with a Patriot or RVibrake 4, lighting and 12V support. Plan time to position, connect and calibrate the portable brake at each departure.

Less daily setup

Installed hydraulic-coach system

Compare an approved bracket/bar combination with Stay-IN-Play DUO or another confirmed installed application. Include coach signals, vehicle brake setup, breakaway and monitoring.

Air-brake motorhome

Installed air-coach system

Compare Air Force One and the required chassis-specific coach connection with the truck hardware, lighting and power plan. A factory air port must be identified and verified.

A useful estimate itemizes the whole connection. Send photos of any equipment you already own so we can separate reusable parts from missing pieces.

Plan my installation
Choose another section ↑
About this topicRead the full introductionTap to close

A low baseplate price is only one line of the project. Compare packages by their installed scope, exact part numbers and verification—not by a headline price alone.

Choose another topicNext section →

Plan your installation

From parts selection to confident hookup.

Tap an option to open it. Tap it again to close it.

Step-by-step installation processTap to readTap to close

Application review & equipment plan

We begin with the Maverick VIN, front-end options and motorhome details. Existing equipment labels and photos help identify usable parts, adapter needs and coach-side work.

Truck inspection & approved bracket installation

The applicable manual determines fascia removal, structural mounting, fasteners and torque, trimming, shutter changes and clearances. Visible damage or missing structure needs to be resolved before relying on the mount.

Brake, breakaway & electrical installation

The brake system, front socket, lighting circuits and power support are routed and secured as a coordinated installation. The selected equipment determines coach-side wiring or air work.

Configuration & functional checks

We verify the actual Ford towing mode, light functions, brake response, breakaway setup, monitor indication and 12V support. Any sensor work is evaluated against the vehicle’s service requirements.

Hookup demonstration & documentation

The handoff should include connecting and locking the bar, inspecting pins, routing cables and the cord, operating the brake, using the exact Ford routine and disconnecting safely. Keep the manuals and written parts list with the RV.

Scheduling, cost and customer handoverTap to readTap to close

Scheduling and cost

Installation scope depends on the selected equipment, what the coach already has and what can safely be reused. Request a VIN-specific written estimate and confirm parts availability before planning a travel date. A remote preliminary discussion is not final fitment approval.

Warranty and follow-up

Ask for the written terms covering the installation and each manufacturer’s equipment. Coverage, exclusions and claim procedures can differ. Contact Stellar first if an installation concern arises so the source can be identified and the appropriate next step arranged.

Choose another section ↑
About this topicRead the full introductionTap to close

Stellar Auto & Mobility Repair installs and evaluates automotive and mobility equipment in West Melbourne. Your estimate should explain the work, the equipment and the final handoff.

Choose another topicNext section →

Inside a real installation

See where the equipment goes.

Tap an option to open it. Tap it again to close it.

2023 Maverick · DUO operating unitView installation photo and explanationTap to close

An underhood placement reference. Secure mounting and service access must follow the kit instructions.

2023 Maverick · floor and cable-anchor areaView installation photo and explanationTap to close

A closer look at the cable-anchor area. Routing, mounting strength and cable geometry are installation-specific.

2025 Maverick · DUO underhood installationView installation photo and explanationTap to close

The refreshed truck has its own packaging considerations. An older installation photo is not a template.

2025 Maverick · G-Force controllerView installation photo and explanationTap to close

Controller mounting and orientation matter. Follow Demco’s setup and adjustment procedure.

2025 Maverick · pedal cylinderView installation photo and explanationTap to close

The pedal connection must apply and fully release the brake without interfering with normal driving.

2025 Maverick Hybrid Lariat · DUO unitView installation photo and explanationTap to close

A second manufacturer installation example. Verify the current Maverick regulator requirement.

2025 Maverick Hybrid Lariat · installed cylinderView installation photo and explanationTap to close

Inspect cable alignment, pedal clearance and secure mounting in the actual vehicle.

2025 Maverick Hybrid Lariat · G-Force controllerView installation photo and explanationTap to close

An alternate installation example. Placement is subject to the current manufacturer instructions.

Previous 15Next 15 photos
Choose another section ↑
About this topicRead the full introductionTap to close

Eight real Maverick installation references from Demco. These show the components in context; they are not represented as Stellar customer vehicles or a substitute for installation instructions.

Choose another topicNext section →

Tow with confidence

Ford Neutral Tow: use the right routine.

Tap an option to open it. Tap it again to close it.

Your selected Ford instructions

Open Ford’s complete section for your truck
Use the manual for your truck, then follow its cluster prompts.Read this important informationTap to close
Use the manual for your truck, then follow its cluster prompts.The procedures below are a reading aid, not a replacement for Ford’s full instructions. Ford notes that online revisions can differ from the manual supplied with the vehicle. Confirm which instructions apply to your VIN and ignition type; do not combine different-year routines.
Entering Neutral Tow · 2025–2026 overviewView the stepsTap to close

Entering Neutral Tow · 2025–2026 overview

Secure the connection

Secure the truck to the motorhome before releasing it to roll. Tow facing forward only.

Select the correct mode

Use accessory mode, then the steering-wheel menu: Settings → Neutral Tow. Follow the display instructions.

Complete and confirm

Fully press the brake, select N and switch the ignition off as directed. Confirm Neutral Tow is enabled and release the parking brake. Stay within 70 mph and any lower applicable limit.

Ordinary Neutral and temporary/car-wash Neutral are different modes.Read this important informationTap to close
Ordinary Neutral and temporary/car-wash Neutral are different modes.Do not assume the N indicator alone confirms recreational towing mode. If the required confirmation is missing, stop before the motorhome moves.
Your scheduled stop routineTap to readTap to close

The scheduled stop routine changes by year

Model yearFord’s routine, summarizedOpen the exact instructions
2022–2023At the start of the day and at intervals of six hours or less: run the engine for a few minutes; with the brake held, select D, then R, then N. Re-enable Neutral Tow before continuing.2022 manual · 2023 manual
2024At the start of the day and at intervals of six hours or less: start the vehicle; with the brake held, select D, then N. Re-enable Neutral Tow and keep the vehicle on for three minutes before continuing.2024 manual
2025–2026 · passive keyStart each day and at intervals of six hours or less. With the vehicle on and brake held, select D, then N. Re-enable Neutral Tow, keep the vehicle on three minutes, then switch it off.2025 manual · 2026 manual
2025–2026 · ignition keyThe current online instructions give a different battery-recharge routine: vehicle on, brake held, P, then run or drive at least 30 minutes. Re-enable Neutral Tow, keep it on three minutes, then switch it off. Driving requires disconnecting the tow setup first.Read the key-type instructions
Exiting tow mode and resetting the brakeTap to readTap to close

Exiting Neutral Tow · 2025–2026

Current online instructions: accessory mode, brake fully pressed, select P, release the brake and switch off. Wait 15 minutes with doors closed and no vehicle interaction before starting. Read the full vehicle-specific instructions before disconnecting or restarting.

Coordinate the brake-system reset

Starting the truck or pressing the pedal can change the supplemental brake’s setup. After Ford’s required routine, repeat the brake manufacturer’s positioning or calibration steps where required. Then recheck the complete towing configuration.

If the truck will not follow the procedure, do not tow it.Read this important informationTap to close
If the truck will not follow the procedure, do not tow it.Low 12V power, a warning message, an incorrect mode or a mechanical/electrical fault needs diagnosis. Do not drag a vehicle that has returned to Park or apply a workaround learned for another Ford model.
Choose another section ↑
About this topicRead the full introductionTap to close

The truck’s model year and ignition type matter. These summaries reflect the linked Ford guidance checked November 9, 2026. Keep the full applicable manual available during travel.

Choose another topicNext section →

Tow with confidence

A deliberate check before every departure.

Use the sequence in your equipment manuals, then make a final walk-around. The first few feet of movement are a confirmation step—not a way to force a bar or vehicle into the correct state.

STELLAR AUTO & MOBILITY REPAIR

Ford Maverick flat-tow departure checklist · 321-477-1234
stellarautoandmobility.com/maverick-flat-tow-redesign

This interactive check helps organize a walk-around. It does not certify the vehicle or replace either manufacturer’s instructions. Checks reset when this page is reloaded.

Open the 12-point departure checklistCheck off the items before departureTap to close
Confirm the exact truck is eligible and review its Ford recreational-towing instructions.Inspect the baseplate, bar, pins, clips and safety cables; check any applicable recall.Confirm the loaded combination is within the coach, hitch, bar, adapter and cable limits.Connect the bar and verify both arms lock according to its manual.Attach safety cables and breakaway at the specified points, with clearance for turns.Connect the electrical cord; keep it clear of the road, heat and moving parts.Confirm the Ford Neutral Tow message, ignition state and parking-brake release.Set up the supplemental brake and verify its driver monitor and breakaway system as instructed.Test running, left/right turn and brake lights in the actual towing configuration.Verify the 12V support is working and the battery is healthy.Walk around for loose hardware, trapped cables, accessories, tire issues and clearance.Plan Ford’s required stops and the correct brake reset; disconnect before backing.

0 of 12 checked

At fuel and rest stopsRead this important informationTap to close
At fuel and rest stopsCheck the connections, tires, cord and visible hardware. Investigate unusual heat, dragging, poor braking, monitor warnings or a changed Neutral Tow state before continuing. Stop in a safe place; do not troubleshoot while moving.
Choose another section ↑
Choose another topicNext section →

Tow with confidence

When something does not look right.

Tap an option to open it. Tap it again to close it.

Choose a symptom and see what to checkTap to readTap to close
What you noticeWhat to check firstWhat to avoid
Neutral Tow will not enableCorrect Hybrid application, accessory/ignition state, full brake input, exact cluster prompts and 12V battery condition.Do not tow in ordinary N, car-wash mode or an unconfirmed mode.
Neutral Tow message remains after exitRecheck the exact exit routine and ignition type; record the message and have the vehicle diagnosed if it persists. Certain earlier trucks have a Ford service message discussed below.Do not assume a software bulletin applies to every VIN or clear warnings without diagnosis.
Dead or weak 12V battery after towingBattery health, actual coach charge output under load, fuse/breaker, ground, cord terminals and brake-system demand.Do not assume a 7-pin plug means charging is active, or disconnect the battery as a generic fix.
One light is wrong or another circuit flashesSocket pin assignments, ground quality, diode orientation, lamp type and combined brake/turn behavior.Do not join circuits by color alone or bypass isolation without the wiring instructions.
Brake dragging, heat or repeated brake alarmStop safely. Check the unit’s positioning, pedal clearance, cable adjustment, setup state and brake-assist configuration. Seek service if the cause is not clear.Do not keep towing to see if it clears. Do not use a universal gain or force setting.
Tow bar binds during disconnectSecure both vehicles against movement, follow the bar’s release procedure and unload the connection as the manufacturer directs.Do not hammer out loaded pins, pull with a strap or back the connected combination.
New radar, driver-assistance or other warning after installationInspect disturbed connectors, sensor mounting, fascia alignment and related service requirements. Diagnose the actual fault.Do not cover the warning with a reset or promise calibration is never required.
Earlier-truck service information · Ford SSM 53562Read this important informationTap to close
Earlier-truck service information · Ford SSM 53562Ford published a service message addressing persistent Neutral Tow warnings or an N indicator on certain earlier Maverick Hybrids with a 4-inch instrument cluster after the exit procedure is not followed. Applicability is specific; diagnosis may involve instrument-cluster software. This is a service message, not a blanket recall or a diagnosis for every truck. Read Ford’s bulletin hosted by NHTSA.
Choose another section ↑
About this topicRead the full introductionTap to close

Stop and identify the cause before continuing. The guide can point you toward the right check; it cannot confirm a vehicle’s mechanical or electrical condition remotely.

Choose another topicNext section →

Maverick flat-tow FAQ

50 questions. The answers you need.

Up to 15 questions per page. Tap a question to read its answer, or choose a topic below.

Choose a question group1. Eligibility & Ford setup · Questions 1–152. Towing stops, baseplates & tow bars · Questions 16–303. Brakes, lights, battery & travel · Questions 31–454. Disconnecting & getting help · Questions 46–50

Previous 15 questionsNext 15 questions

1. Eligibility & Ford setup · Questions 1–15

1. Which Ford Mavericks can be flat towed behind an RV?Read the answerClose the answer

The 2022–2024 2.5L Hybrid FWD and eligible 2025–2026 2.5L Hybrid FWD/AWD configurations have Ford four-wheel-down towing instructions. The 2.0L EcoBoost does not gain that approval just because a baseplate fits. Start with the actual model year, powertrain and VIN; then check the separate equipment application. A trim badge alone is not enough.

Check my truck
2. Can a 2025 or 2026 Maverick Hybrid AWD be flat towed?Read the answerClose the answer

Yes, Ford lists four-down capability for the 2.5L Hybrid AWD in these model years, subject to Ford’s towing procedure. This does not approve an EcoBoost AWD, and it does not mean an earlier baseplate fits the newer front end. Confirm the VIN, ignition type and current baseplate listing before buying equipment.

See year and powertrain guidance
3. Can I flat tow an EcoBoost, Tremor or Lobo Maverick?Read the answerClose the answer

Do not use the Hybrid procedure on a 2.0L EcoBoost truck. Ford does not approve that gasoline powertrain for recreational four-down towing. Check the actual drivetrain rather than assuming an off-road or performance package makes it towable. For an AWD configuration that is not approved, review Ford’s all-wheels-off-ground transport instructions.

Check the actual configuration
4. Do I need the 4K Tow Package to flat tow my Maverick?Read the answerClose the answer

Ford’s four-down eligibility is based on the vehicle configuration and towing procedure, not on buying the 4K trailer-towing package. The Maverick’s trailer rating describes what the truck can pull; it is not the rating for an RV pulling the truck. Flat towing still needs its own baseplate, tow bar, braking, lighting and power plan.

See the complete flat-tow system
5. Is a tow dolly or a trailer an alternative to flat towing?Read the answerClose the answer

They are different towing methods with different approvals. Do not assume lifting two wheels makes any Maverick safe to tow. Ford’s gasoline FWD instructions allow a front-wheel dolly; AWD instructions require all wheels off the ground for that transport method. Check the exact year and powertrain manual, plus the dolly or trailer rating, before choosing.

Check the factory transport instructions
6. How do I know whether my motorhome can tow the truck?Read the answerClose the answer

Use the truck’s actual loaded weight, including cargo and installed equipment. Compare it with the motorhome’s remaining combination-weight allowance, receiver limit and every towing component’s rating. Any adapter or extension may add another restriction. A higher-rated tow bar cannot raise the motorhome’s or hitch’s limit; the applicable lowest limit controls.

Compare ratings and equipment
7. Can flat towing affect my Ford warranty?Read the answerClose the answer

Ford warns that damage caused by failing to follow its towing instructions may not be covered. That is different from a promise that every towing-related repair will be covered—or that the entire warranty automatically disappears. Keep the correct manual, installation invoice, part numbers and service records. Ford must evaluate a specific claim against the vehicle’s warranty terms.

Read Ford’s instructions
8. Does flat towing add miles to the odometer?Read the answerClose the answer

We have not found a Maverick-specific Ford statement in the reviewed towing instructions that guarantees odometer behavior for every year and software version. Confirm it with Ford for your VIN if it affects a purchase decision. Keep a separate tow-mileage log regardless: tires, bearings and braking equipment still experience use, even when the odometer does not reflect it.

Open the departure checklist
9. Where can I download the factory manual and just the towing instructions?Read the answerClose the answer

Open Ford manuals below and choose your model year. Each card provides the full factory PDF, a separate Ford online towing section, and a link to the towing pages inside the PDF with the printed page numbers. To save only those pages, use the PDF viewer’s print dialog, choose that page range and select Save as PDF. The separate online section is Ford’s webpage, not a separate factory PDF.

Open year-specific downloads
10. How much does a complete Maverick flat-tow installation cost?Read the answerClose the answer

A useful written estimate starts with your VIN, motorhome, chosen equipment and anything you already own. It should separate baseplate installation, tow bar and adapters, supplemental braking, lights, charging, any coach-side work and final testing. Online totals may leave out important pieces. Send the details through our estimate form so Stellar can confirm fitment, availability and the actual scope.

Request an itemized estimate
11. Is putting the shifter in Neutral the same as Neutral Tow?Read the answerClose the answer

No. The N position alone does not confirm recreational-towing preparation. Use Ford’s Neutral Tow menu and complete the cluster prompts, then confirm that the mode is enabled. Do not substitute car-wash or temporary-neutral instructions for the recreational-towing procedure. If the expected confirmation is missing, stop and resolve it before towing.

Open the Ford setup walkthrough
12. How do I turn Neutral Tow on?Read the answerClose the answer

Secure the truck to the towing vehicle as Ford directs. The reviewed 2025 procedure uses accessory mode, the steering-wheel menu, Settings, then Neutral Tow. Follow the cluster prompts, fully apply the brake, select N and switch the ignition off. This is an orientation to the controls: use your exact year’s full instructions and confirm the enabled message before moving.

Read the complete year-specific steps
13. Do I leave the ignition on, and can the key stay in my pocket?Read the answerClose the answer

Ford’s setup ends with the ignition off. Key handling depends on ignition type: a physical key cannot be removed with the transmission in N and the vehicle off. Do not copy a push-button truck’s key routine onto a keyed truck. The required daytime restart procedure is separate from the ignition state used while towing.

Check ignition and key instructions
14. Should the parking brake be released and the steering wheel free?Read the answerClose the answer

Yes. Ford requires the parking brake released for four-down towing. The steering must also be free to follow the motorhome; do not strap the wheel in place or tow with a steering lock engaged. Secure the vehicles against unintended movement while setting up or disconnecting, then complete the checks in Ford’s and the tow-bar maker’s instructions.

Review the departure checks
15. What is the maximum flat-towing speed: 65 or 70 mph?Read the answerClose the answer

The reviewed Ford Maverick Hybrid instructions specify a maximum of 70 mph (113 km/h). That is a ceiling, not a recommended cruising speed. Use a lower limit whenever the equipment instructions, road conditions or applicable traffic rules require it. Do not borrow a limit from another Ford model or from emergency-towing instructions.

See Ford’s towing limits
16. How often must I stop and start the Maverick while towing?Read the answerClose the answer

Ford requires the start-and-shift routine at the beginning of each day and at intervals of six hours or less. Plan stops before that limit. The exact gear sequence and running time depend on model year, ignition type and manual revision. Re-enable Neutral Tow before resuming, and reset the supplemental brake when its instructions require it.

Review the required stop routine
17. Why are the restart instructions different for keyed and push-button trucks?Read the answerClose the answer

Ford publishes different sequences. The 2022–2023 instructions describe running the engine and shifting D, R, then N. The reviewed 2024 online section describes D then N and a three-minute period after re-enabling. The 2025–2026 instructions distinguish passive-key operation from a physical-key routine that includes at least 30 minutes running in P or driving to recharge. Use the instructions for your truck; do not combine them.

Compare the correct Ford manual
18. How do I exit Neutral Tow, and what is the 15-minute wait?Read the answerClose the answer

For the reviewed 2025–2026 procedure: switch to accessory mode, fully press the brake, select P, fully release the pedal, then switch the ignition off. Ford then requires 15 minutes with the doors closed and no interaction before starting the engine. Ford does not explain the engineering reason in this section. Follow the complete exit procedure whenever exiting the mode, including a towing stop; ask Ford to resolve any VIN-specific conflict.

Read Ford’s exit procedure
19. Can a battery charge line replace Ford’s six-hour stops?Read the answerClose the answer

No. A charge line supports the 12V battery; it does not cancel the start-and-shift routine. Ford’s 2025 guidance contains both external-power guidance for add-on braking and the required towing stops. Complete each requirement independently, and confirm Neutral Tow and the brake system are ready again before continuing.

Review battery support
20. What if Neutral Tow will not enable or the expected message is missing?Read the answerClose the answer

Do not move the combination in an unconfirmed towing mode. Recheck the exact Hybrid application, accessory/ignition state, brake input and cluster prompts. Low 12V power is another item to investigate because enabling the mode requires battery power. If the sequence will not complete, record the message and obtain diagnosis rather than repeatedly shifting or guessing.

Open towing troubleshooting
21. What baseplate brands and part numbers should I compare?Read the answerClose the answer

The guide compares Roadmaster, Blue Ox, Demco and etrailer applications. Examples include Roadmaster 524470-5 and Blue Ox BX2913 for earlier trucks, and Roadmaster 524480-5 and Blue Ox BX2917 for the later front end. Open the filtered baseplate section for the full list, installed references and instructions. These examples are not a fitment guarantee: verify the actual year, VIN, trim and current exclusions.

See all baseplate options
22. Will a 2022–2024 baseplate fit a 2025 or 2026 truck?Read the answerClose the answer

Do not assume it will. The front-end update changes the application, and manufacturers list different earlier and later kits. Match the actual part number and current installation instructions before ordering. Transferring an old bracket is also a separate issue: Roadmaster warns against reinstalling a used baseplate on another vehicle and limits its warranty to the original installation.

Compare early and later applications
23. Which baseplate needs the least trimming, and is installation reversible?Read the answerClose the answer

There is no universal no-cut answer. Review the current instructions for the exact kit, including fascia trimming, drilling, active-grille-shutter work and any factory-option exclusions. Removable arms do not make the permanent installation reversible. Tell Stellar that minimizing visible changes matters before parts are chosen, and compare the required modifications alongside the installed appearance.

Open installation documents and photos
24. Which baseplate looks cleanest when disconnected, and are these Stellar photos?Read the answerClose the answer

Removable-arm and tabless designs reduce visible connection points, while the fixed bracket, electrical socket and breakaway switch remain. Compare the real installed-reference photos and discuss accessible mounting locations. The labeled baseplate pictures are reference installations from etrailer, not claimed as Stellar customer work. The hero is a licensed real-vehicle photograph. Current kit instructions control the actual installation.

View the real installation references
25. Will baseplate installation affect adaptive cruise, sensors or grille shutters?Read the answerClose the answer

It depends on the exact kit and vehicle equipment. Mounting work can be near shutters, wiring, fascia and driver-assistance components. Follow the application exclusions and installation instructions, preserve clearances, and diagnose any new warning. Do not assume every trim needs calibration—or that none does. Review factory service requirements for anything disturbed during installation.

Review the installation process
26. Can I mix a Blue Ox tow bar with a Roadmaster baseplate?Read the answerClose the answer

Only when the manufacturers approve the exact combination and adapter. Check both part numbers, the tow-bar ends, pin hardware, crossbar requirements and ratings. A compatible brand name alone is not enough. Direct-Connect and crossbar setups are different, and some older bars require serial-number checks. An adapter can change the connection length and height as well.

Compare bars and adapter requirements
27. What tow-bar rating do I need, and what does nonbinding mean?Read the answerClose the answer

Choose a rating that covers the truck’s loaded weight and remains within every other component limit. Nonbinding release features help release tension during an approved disconnect procedure; they do not raise capacity or permit backing. Compare actual model numbers and receiver sizes. For example, the guide distinguishes Blue Ox Apollo BX7475 with a 2-inch receiver from BX7470 with a 2.5-inch receiver.

Compare all tow-bar choices
28. Can I reuse my tow bar, brake or other equipment from a previous vehicle?Read the answerClose the answer

Possibly, after an application and condition review. Send clear label photos, part and serial numbers, all adapters and pins, receiver size, and service history. A portable brake or tow bar may be reusable; the vehicle-specific baseplate needs its own approval. Check missing accessories, wear and recalls before comparing reuse with new equipment. Do not assume an older bar’s end fittings match a new baseplate.

Request an existing-equipment review
29. Do I need a high-low adapter between the RV and tow bar?Read the answerClose the answer

Measure the loaded combination on level ground at the motorhome receiver and the baseplate connection points. Compare that difference with the exact tow-bar manual. For example, the Nighthawk manual permits no more than three inches above or below level. Use an approved adapter if needed and account for its rating and any receiver-extension restrictions; do not stack adapters by guesswork.

Read height and adapter guidance
30. Are safety cables and the brake breakaway cable the same thing?Read the answerClose the answer

No. Safety cables are backup mechanical connections; the breakaway cable activates the towed-vehicle brake if separation occurs. Install and route both according to their manufacturers, with secure attachment, adequate turning clearance and no dragging or binding. A breakaway cable does not replace safety cables, and the electrical cord does neither job. Include all three in the walk-around.

Open the connection checklist
31. Do I need supplemental brakes even with a large motorhome?Read the answerClose the answer

Plan a compatible supplemental braking and breakaway system as part of the complete setup. The motorhome’s brakes do not automatically operate the truck’s service brakes. Equipment requirements, the actual loaded combination and rules along the route must be checked; an RV’s size alone does not settle the question. Have the installed system tested and demonstrate its monitor and breakaway operation before departure.

Compare supplemental brake options
32. Does the motorhome’s trailer brake controller operate the Maverick brakes?Read the answerClose the answer

A conventional electric-trailer brake controller is not automatically a Maverick supplemental brake. A towed-vehicle system must operate the truck’s service brakes and provide its intended breakaway function. Identify the coach brake type and the chosen system before assuming an existing controller is enough. Some systems use coach brake-light information, but that is not the same as an electric-trailer brake output.

See how the brake systems differ
33. Is a portable brake easier, or should I choose a permanently installed system?Read the answerClose the answer

Portable systems can move between approved vehicles but need positioning, pedal attachment and setup each trip. They still require suitable power and breakaway wiring. Installed systems trade more initial installation work for a different daily routine. Compare the controls you can comfortably reach, setup effort, monitoring, coach compatibility and manufacturer approval for the Maverick’s brake assist.

Compare portable and installed brakes
34. Does the Maverick Hybrid need a special brake setting?Read the answerClose the answer

The selected brake must support the vehicle’s brake-assist behavior. Do not copy a force setting from a different vehicle. For example, the Blue Ox Patriot manual requires Hybrid mode for hybrids or continuous power-assist brakes. Other systems have their own installation and adjustment requirements. Verify both proper braking and complete pedal release, then demonstrate the monitor to the driver.

Read hybrid brake requirements
35. Does an air-brake motorhome need different equipment from a hydraulic-brake RV?Read the answerClose the answer

Yes, coach brake type matters. Demco specifies Stay-IN-Play DUO for a hydraulic-brake coach and recommends Air Force One for an air-brake coach. Other products have their own compatibility rules. Confirm the motorhome chassis and whether any factory or aftermarket towed-brake connection is already fitted; a connector’s appearance alone does not establish compatibility.

Match braking to the motorhome
36. Can I use my NSA Ready Brute Elite II surge-brake tow bar?Read the answerClose the answer

It may be usable with an approved baseplate connection and the correct brake installation. The Ready Brute Elite II combines a tow bar and mechanical surge-brake mechanism, but still requires its specified vehicle brake cable, adjustment and breakaway arrangement. Inspect the exact model, clevises and existing parts. Owning the bar alone does not mean the Maverick-side installation is complete.

Review Ready Brute and other bars
37. Do I need diodes, a plug-in harness or separate lights?Read the answerClose the answer

Choose a lighting method approved for the exact lamp type and vehicle. A diode or compatible harness arrangement uses the truck’s lamps while managing circuit isolation; separate lamps are a different installation. Test running lights, both turns and brake signals through the actual RV connection. The selected braking system may also need a stop-light signal or relay, depending on the wiring behavior.

Compare lighting and wiring choices
38. Why does the truck need a charge line if the ignition is off?Read the answerClose the answer

Towing electronics and supplemental brakes can use 12V power. Ford’s current 2025–2026 guidance calls for an external 12V supply when an add-on flat-tow brake is used. A working system needs the coach supply, protected truck circuit, compatible cord and reliable ground. Test charging through the connected rig under load; simply plugging in a seven-pin cord does not prove that charging is working.

Review the complete charge-line path
39. Can I plug a portable brake into the factory 12V outlet?Read the answerClose the answer

Only if the outlet remains powered in the required towing state and meets the brake maker’s requirements. Check after the vehicle’s power timeout, not just immediately after shutting it off. A properly protected dedicated outlet may be needed. CURT specifically says RVibrake4 must have power from the towed vehicle’s battery, so a breakaway does not remove its only supply.

Review brake power and charging
40. Must I reset the supplemental brake after starting the Maverick at a stop?Read the answerClose the answer

Follow that brake’s reset instructions every time. Blue Ox explicitly requires resetting the Patriot whenever the towed vehicle is started. Reconfirm the hybrid setting, pedal position, readiness and monitor as directed. Ford’s Neutral Tow procedure and the brake’s setup are separate tasks; completing one does not prove the other is ready.

Review the restart and departure checks
41. Can I back up just a few feet with the Maverick attached?Read the answerClose the answer

Disconnect before backing. Reverse movement can damage the tow bar, steering or mounting equipment. Nonbinding releases and removable baseplate arms do not make backing acceptable. Plan fuel stops, parking and campsites with a forward exit, and use the manufacturer’s secured disconnect procedure if you need to reposition.

Open the travel checklist
42. What should I check before every departure?Read the answerClose the answer

Confirm the correct Ford towing mode, released parking brake and free steering; locked tow-bar arms, pins and clips; safety and breakaway connections; cord routing and lights; brake readiness and monitor; and working 12V support. Check tires, clearance and loose hardware. Use the full 12-point checklist and equipment manuals, then make the initial movement and locking checks exactly as the tow-bar maker directs.

Open or download the departure checklist
43. Can I leave the truck connected overnight?Read the answerClose the answer

Physical attachment does not remove the next morning’s setup requirements. Secure both vehicles against movement and follow Ford’s and the brake maker’s instructions for any mode or power changes. Do not assume the RV keeps charging the truck while parked. At the next departure, perform the daily Ford routine and recheck every connection, light, brake and power supply.

Review the next-day checks
44. What if the battery dies, and is there a voltage where Neutral Tow drops out?Read the answerClose the answer

Stop towing if power, brake readiness or towing-mode status is uncertain. Ford says battery power is required to enter and exit Neutral Tow; the reviewed instructions do not publish a universal safe cutoff voltage. Do not assume a dead battery is harmless or disconnect it as a general fix. Diagnose battery health, charge output, grounds, protection devices and brake demand before continuing.

Open battery and towing troubleshooting
45. What should I do about hot brakes, dragging or a brake alarm?Read the answerClose the answer

Stop safely and investigate before continuing. Check pedal clearance, brake-unit position, cable adjustment, breakaway-pin seating and the correct assist/setup configuration. A system must fully release the truck’s brakes. Do not increase force, bypass the alarm or keep driving to see whether it clears; get service when the cause is uncertain.

Review brake troubleshooting
46. How do I disconnect when the tow bar is binding?Read the answerClose the answer

Secure the vehicles against movement and use the exact bar’s release procedure to unload the connection. Uneven ground and side loading can make release difficult. Do not hammer loaded pins out, pull on the setup with a strap or back the connected combination. If the bar cannot be unloaded as instructed, get help before removing hardware.

Open the tow-bar operating manuals
47. Why does a turn signal stop flashing when the truck’s brake is applied?Read the answerClose the answer

The tow wiring and the truck’s own brake-light signal may be interacting. Check combined brake/turn behavior, lamp type, diode orientation, socket pin assignments and grounds against the selected wiring instructions. A relay or other approved interface may be required for that setup. Do not splice by wire color alone or buy a relay without first identifying the actual circuit behavior.

Review lighting and brake-signal integration

Roadmaster’s 2022–2024 Maverick Hybrid entries specifically call out brake-light relay 88400 with supplemental braking. Its 2025–2026 entries identify an unusable OEM brake switch and list 751513 or 751000 for the required brake signal. A relay, signal switch and lamp diode perform different functions; use the year-specific application described in the lighting chapter.

48. Is a stuck Neutral Tow message a recall, and should I check equipment recalls?Read the answerClose the answer

A service message is not automatically a recall. Ford SSM 53562 addresses a persistent tow warning/N display on certain earlier Hybrid XL/XLT trucks with a four-inch cluster; the document’s heading and body differ in year wording, so verify VIN applicability and diagnosis. Separately, check tow-bar and brake recalls using actual model and serial numbers. Follow the manufacturer’s inspection, repair and stop-use instructions before towing.

Read the service information and next checks
49. Can Stellar install this while I am traveling through Florida?Read the answerClose the answer

Contact us before committing to a travel date. Send the Maverick VIN, motorhome details, equipment labels and your timing so we can review the application, parts and work required. Installation is at our West Melbourne shop. A confirmed scope and appointment are needed before arrival; the estimate should also include a complete hookup demonstration and functional checks.

Request an appointment and estimate
50. Does this FAQ replace the manuals, and what if two instructions disagree?Read the answerClose the answer

No. Ford controls vehicle eligibility and operation; each equipment manufacturer controls its fitment, installation and use. Check the exact year, VIN, ignition type, part number and document revision. Ford notes that online information may differ from the manual supplied with the vehicle. If instructions conflict, ask Ford or the equipment maker to resolve applicability before towing. This guide helps organize the questions and original documents.

Open manufacturer documents

Previous 15 questionsNext 15 questions

Questions selected from Maverick owner discussions and common installation concerns. Answers checked against the linked manufacturer documents. Last reviewed November 10, 2026. Confirm the instructions for your exact vehicle and equipment before towing.

Products you want to ask about

Choose as many products as you like while reading. You can compare alternatives in one request.

    More information Product pricing Installed pricing

    Your selected products will be included with the estimate form below.

    Continue to contact form ↓

    Stellar Auto & Mobility Repair · West Melbourne, FL

    Let’s build the right setup for your trip.

    Use the estimate form below. A few specific details help us check the application and prepare a useful equipment plan.

    Your selected truck will be added to the form. You can edit it.

    Use selected truck
    • Maverick year, trim, powertrain and VIN
    • Motorhome year, make, model, chassis and brake type
    • Existing baseplate, tow-bar and brake part numbers
    • Your travel timing and any installation preferences

    7791 Industrial Rd · West Melbourne, FL 32904
    Monday–Friday 8:30–5:00 · Saturday by appointment

    Choose another topicNext section →
    Installed baseplate referenceClose ×

    Motorhome brake type

    List any tow bar, baseplate, braking system, wiring or charging kit you already own. Or tell us what you want help with: fitment, product comparisons, pricing, or installation. If you have no equipment yet, say “none.”

    Our Services

    Opening Hours

    MONDAY

    TO

    8:30 AM

    5:00PM

    TUESDAY

    TO

    8:30 AM

    5:00PM

    WEDNESDAY

    TO

    8:30 AM

    5:00PM

    THURSDAY

    TO

    8:30 AM

    5:00PM

    FRIDAY

    TO

    8:30 AM

    5:00PM

    SATURDAY

    APT

    BY

    ONLY

    SUNDAY

    APT

    BY

    ONLY

    Contact Us

    7791 Industrial Rd.
    West Melbourne, FL 32904 USA

    ​

    Office: 321-477-1234
    info@stellarautoandmobility.com

    Stellar Auto & Mobility Repair Map Location

    © 2024 by Stellar Auto & Mobility Repair

    Veteran Own Small Business
    Stellar Auto & Mobility Repair Logo
    bottom of page